Gill WindSonic User Manual Download Page 72

Page: 72 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

Unit Checks.

If commands are typed (followed by the Enter key) that the unit will not accept then
ILLEGAL COMMAND LINE will be reported.

Commands that will be accepted are:-

REPORT then press Enter key (see below).

SERIAL then press Enter key (see below).

SWVER then press Enter key (see below).

Type Q then press Enter key (see below) this allows data to scroll on screen.

The Wind data string can be examined to check for instance that the wind direction and
speed are output and the 2 digit status code is 00.

If the 2 digit Status Code is other than 00 refer to Para 14.7.

Note: Once the unit is turned off and back on again it will return to SDI-12 mode

If you need to get back into Gill continuous data then you have to perform the safe mode
steps again.

14.9 WindSonic Option 4 Electrical Conformity

See Para 13.3.

Summary of Contents for WindSonic









































































Search results

Summary of Contents for WindSonic

Reviews:

Related manuals for WindSonic

Brands by name

Popular brands

Gill WindSonic, User Manual

Search results

Summary of Contents for WindSonic

Reviews:

Related manuals for WindSonic

Brands by name

Popular brands