Gill WindSonic User Manual Download Page 20

Page: 20 / 72

WindSonic Doc No 1405 PS 0019 Issue 28 November 2019

7.4 Connecting to a PC using RS232 (Option 1 Sensor)

Notes

The cable length for reliable operation is limited to 6.5m (20ft).

(

See

Section 7.3.1 Cable length.)

For longer cable runs, we recommend using the WindSonic configured with RS422
output, and a RS422/232 converter at the PC.

Wiring connections below are not applicable to WindSonic Options 2 and 3 set for
RS232 operation.

WindSonic

9 Way circular connector

Typical PC or RS232 to USB

Converter Serial Port

9 Way ‘D’ Connector

Signal names

Pin nos.

Cable – 3 twisted

pairs

Signal names

Pin no's

TXD

RXD

TXD

Signal

Ground

Signal Ground

Do NOT

connect

at this end

N/A

Screen and drain

wires

Chassis

ground

N/A

V supply -

–

DC Power supply

(See Para 7.3.2)

Default Settings

The WindSonic Option 1

unit is factory configured with the following default settings:

M2, U1, O1, L1, P1, B3, H1, NQ, F1, E3, T1, S4, C2, G0, K50,

Summary of Contents for WindSonic









































































Search results

Summary of Contents for WindSonic

Reviews:

Related manuals for WindSonic

Brands by name

Popular brands

Gill WindSonic, User Manual

Search results

Summary of Contents for WindSonic

Reviews:

Related manuals for WindSonic

Brands by name

Popular brands