manualshive.com logo in svg

Gill WindSonic, User Manual

Share
Download
Gill WindSonic User Manual Download Page 40

WindSonic                      Doc No  1405 PS 0019 Issue 28                November 2019 

 

39 

10  CONFIGURING 

Gill Wind Software may be used to configure the WindSonic; alternatively, the user may 
elect to use another terminal emulator package such as Windows HyperTerminal. This 
section describes the commands used to change User and Communications settings. 

10.1  Wind 

Wind software is available on the supplied CD or to download, free of charge, from the Gill 
Instruments Limited website 

http://gillinstruments.com/main/software.html

 . 

Wind software allows the unit configuration to be changed and to be able to display the 
Digital Data String on a PC screen. 

NOTE: Wind is not compatible with WindSonic Option 4 – SDI-12 or WindSonic units 
prior to serial number 08100001 with a yellow or blue tab adjacent to the North Marker. 

Connect both WindSonic transmit and receive data lines to the PC to establish 2 way 
communications. 

Open Wind Software and select the appropriate Com Port from the drop down menu and 
click on OK to reach the data screen.  

 

If data is not correctly displayed then on the Menu click on Tools/Synch Comms. 

The Sensor will be interrogated and Sensor Baud Rate and Mode settings detected and 
reported.  

Wind software settings will be adjusted to match those of the sensor to show data scrolling 
on screen.  

If after Synch Comms there is still a problem, repeat Synch Comms or switch off the sensor 
and switch back on again and repeat above procedure. 

Note: - It is also possible to use Wind as a Terminal Program and change settings using 
the Configuration Mode of operation (Commands are listed in Para’s 10.4 to 10.7.1). 

Summary of Contents for WindSonic









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands