GILES FSH-2-PH Manual Download Page 55

Page: 55 / 66

Troubleshooting

FSH

−

6.01

Troubleshooting Procedures

−

continued

Problem

Probable Cause

Corrective Action

Fryer will not power

up:

•

[HOOD POWER]

light

•

[

FILTER MISSING]

light

•

[FRYER POWER]

light

OFF

a. Baffle filter is missing or not

properly installed

Install filter / check positioning.

b. Charcoal filter is missing or not

properly installed

Install filter / check positioning.

c. Faulty filter switches.

Test & replace as needed.

Fryer will not power

up:

•

[HOOD POWER]

light

•

[

FILTER MISSING]

light

OFFN

•

[FRYER POWER]

light

OFF

• No alarm sounding

a. Fire Suppression system is not

armed.

Contact Ansul service company.

b. Ansul switch is faulty

Contact Ansul service company.

Fryer will not power

up:

•

[HOOD POWER]

light

•

Continuous (steady) tone

alarm

sounding.

•

[FRYER POWER]

light

OFF

a. Baffle or charcoal filter clogged

Replace charcoal filter with new •
Clean baffle filter.

b. Hood exhaust outlet excessively

block

Clear of any obstructions.

c. Vacuum switch is out of

adjustment

Test & adjust vacuum switch.

d. Kinked or blocked vacuum line

Remove vacuum line kinks or
blockage.

e. Fan running slow or blades are

loaded with grease build

up.

Check voltage and inspect blower;
clean if needed

Fryer will not power

up:

•

[HOOD POWERED]

light

•

[WASH]

light

•

Intermittent (beeping) tone

alarm

sounding.

•

[FRYER POWER]

light

OFF

a. Excessive grease film built up on

collector fins; too dirty

Clean the EAC cell,

Section 4.04.2

b. EAC cell is not installed

Install clean EAC cell.

c. EAC driver board is faulty

Test & replace EAC power supply if
needed.

d. Poor connection at contact

plate; dirty contacts, mis

alignment, faulty contacts.

Check cell position, clean contacts,
inspect contact plate & replace if
needed.

e. Ionizer wire(s) missing

Replace missing wire(s)

Fryer is ON:

•

[HOOD POWER]

light

•

[CHECK]

light

•

alarm sounding, but cell is

NOT

cleaning air

a. Ionizer wire broken & touching

chassis.

Replace ionizer wire.

b. Collector fins shorted to ground

by moisture.

Dry cell, determine cause of
moisture, cool air being drawn into
hood creating condensation.

Summary of Contents for FSH-2-PH



































































Search results

Summary of Contents for FSH-2-PH

Reviews:

Related manuals for FSH-2-PH

Brands by name

Popular brands

GILES FSH-2-PH, Manual

Search results

Summary of Contents for FSH-2-PH

Reviews:

Related manuals for FSH-2-PH

Brands by name

Popular brands