GILES FSH-2-PH Manual Download Page 39

Page: 39 / 66

Operation

FSH-2-PH

4.02.3

Baffle Filter Installation

BAFF

LE FIL

TER

BAFFL

E FILTE

BAFFL

E FILTE

BAFFL

E FILTE

Switch arm

must be
actuated by
the Baffle
Filter when
installed, as
shown

①

Insert back edge of filter into hood

(to the back wall)

②

Lift front edge up behind

Front Header Panel

③

Pull filter forward until front edge rests on

support ledge

inside

front panel

④

Allow back edge to drop down and rest on

studs in the rear channel

IMPORTANT!

As shown above, the filter body must engage and actuate the curved actuator lever located at the rear of

hood, on the right side. Filter must be installed so that the slats/slots are vertical, NOT

horizontal.

The Baffle Filter has sharp exposed edges, which may cause cuts. Use due caution when handling and
cleaning. Heavy duty rubber gloves are advised.

Summary of Contents for FSH-2-PH



































































Search results

Summary of Contents for FSH-2-PH

Reviews:

Related manuals for FSH-2-PH

Brands by name

Popular brands

GILES FSH-2-PH, Manual

Search results

Summary of Contents for FSH-2-PH

Reviews:

Related manuals for FSH-2-PH

Brands by name

Popular brands