Gigabyte TO22-Z61 User Manual Download Page 107

Page: 107 / 141

- 107 -

BIOS Setup

Lan Channel 1

Configuration Address source

Select to configure LAN channel parameters statically or dynamically (DHCP). Unspecified option will not

modify any BMC network parameters during BIOS phase.

Options available: Unspecified/Static/DynamicBmcDhcp. Default setting is

Unspecified

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.

Please note that the IP address must be in three digitals, for example, 192.168.000.001.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

Real-time synchronize BMC network parameter values

Press [Enter] to synchronize the BMC network parameter values.

Summary of Contents for TO22-Z61














































































































































Search results

Summary of Contents for TO22-Z61

Reviews:

Related manuals for TO22-Z61

Brands by name

Popular brands

Gigabyte TO22-Z61, User Manual

Search results

Summary of Contents for TO22-Z61

Reviews:

Related manuals for TO22-Z61

Brands by name

Popular brands