Gigabyte TO22-Z61 User Manual Download Page 50

Page: 50 / 141

BIOS Setup

- 50 -

5-2-2-2

Device Hardware Configuration Menu

Main Configuration Page > Device Hardware Configuration Menu

Configures the device and port specific parameters. Please refer to help text defined per configurable

parameter for more information.

DCB Protocol

Enable/Disable the DCB Protocol.

Options available: Enabled/Disabled. Default setting is

Enabled

Number of VFs per PF

Displays the number of VFs per PF in multiple of 8 (0 to 64).

Max PF MSI-X Vectors

Displays the maximum number of PF MSI-X Vectors. (0 to 64).

UEFI Boot Mode

Specifies Driver Boot Mode in UEFI environment.

Default setting is

UNDI

MFW Crash Dump Feature

Enables MFW bootcode to collect critical device and system information during unanticipated system
crash.

Options available: Enabled/Disabled. Default setting is

Enabled

Summary of Contents for TO22-Z61














































































































































Search results

Summary of Contents for TO22-Z61

Reviews:

Related manuals for TO22-Z61

Brands by name

Popular brands

Gigabyte TO22-Z61, User Manual

Search results

Summary of Contents for TO22-Z61

Reviews:

Related manuals for TO22-Z61

Brands by name

Popular brands