Gigabyte TO22-Z61 User Manual Download Page 101

Page: 101 / 141

- 101 -

BIOS Setup

5-4-2

Error Management

Platform First Error Handling

Enable/Disable PFEH.

Options available: Enabled/Disabled. Default setting is

Enabled

MCA Error Threshold Count

MCA Error Threshold Count. 0 - Disable Error.

Options available: 0/1/5/10/100/1000. Default setting is

DRAM Address/Command Parity With Replay

RCD Parity

Enable/disable Registering Clock Driver (RCD) Parity (RDimmParEn).

Options available: Enabled/Disabled. Default setting is

Enabled

DRAM Address Command Parity Retry

Enable/disable DRAM Address Command Parity Retry.

Options available: Enabled/Disabled. Default setting is

Disabled

DRAM Write Data CRC with Retry

Write CRC Enable

If CRC is enabled, the memory is expecting CRC to be sent with the write data.

Options available: Enabled/Disabled. Default setting is

Disabled

Summary of Contents for TO22-Z61














































































































































Search results

Summary of Contents for TO22-Z61

Reviews:

Related manuals for TO22-Z61

Brands by name

Popular brands

Gigabyte TO22-Z61, User Manual

Search results

Summary of Contents for TO22-Z61

Reviews:

Related manuals for TO22-Z61

Brands by name

Popular brands