Gigabyte GN-BR02G User Manual Download Page 68

Page: 68 / 83

GN-BR02G 2.4GHz Wireless Broadband Router

Appendix D

Troubleshooting

Problem 1:

Cannot connect to the Router’s Web-based Utility.

Response:

•

Make sure that your Router uses DHCP, and make sure your
PC’s IP address is on the same subnet as the router.

•

Check to see if your web browser is automatically detecting
LAN settings.

•

Try closing all web browsers and trying again.

Make sure that your Router uses DHCP, and make sure your PC’s IP
address is on the same subnet as the router.

Step 1

Click the

Start

button. Select

Run

, then type “command”. Press OK.

Step 2

At the command prompt, type “

ipconfig /release

” and press the

ENTER

key.

Step 3

At the next command prompt, type “

ipconfig /renew

” and press the

ENTER

key.

Summary of Contents for GN-BR02G




















































































Search results

Summary of Contents for GN-BR02G

Reviews:

Related manuals for GN-BR02G

Brands by name

Popular brands

Gigabyte GN-BR02G, User Manual

Search results

Summary of Contents for GN-BR02G

Reviews:

Related manuals for GN-BR02G

Brands by name

Popular brands