Gigabyte GN-BR02G User Manual Download Page 9

Page: 9 / 83

GN-BR02G 2.4GHz Wireless Broadband Router

LEDs

Figure 2: LED Layout

The table below describes the LED indicators on the front
panel of the GN-BR02G. All LEDs are green when lit.

LED

STATUS

DESCRIPTION

Green

Power is supplied to the Router

Power

Off

Power is NOT supplied to the Router

WLAN

Flashing

Data is being transmitted wirelessly

WAN port has detected a wired link with a
DSL or Cable modem.

WAN

Flashing

Data is being transmitted / received
through WAN port.

LAN port has detected a link with a
10/100Mbps device

LAN

Flashing

Data is being transmitted / received
through LAN port.

Key Features

Conforms to IEEE 802.11g specification.

Wireless transmits data rate up to the maximum speed of 108Mbps*.

Supports 64-bit /128-bit/152-bit WEP encryption, 802.1x, and WPA™.

Power LED

WLAN LED

LAN LED

(4)

WAN LED

Summary of Contents for GN-BR02G




















































































Search results

Summary of Contents for GN-BR02G

Reviews:

Related manuals for GN-BR02G

Brands by name

Popular brands

Gigabyte GN-BR02G, User Manual

Search results

Summary of Contents for GN-BR02G

Reviews:

Related manuals for GN-BR02G

Brands by name

Popular brands