Gigabyte GA-870A-USB3 User Manual Download

Page: 39 / 96

- 39 -

BIOS Setup

Date (mm:dd:yy)

Sets the system date. The date format is week (read-only), month, date and year. Select the desired field

and use the up arrow or down arrow key to set the date.

Time (hh:mm:ss)

Sets the system time. For example, 1 p.m. is 13:0:0. Select the desired field and use the up arrow or

down arrow key to set the time.

IDE Channel 0, 1 Master/Slave

IDE HDD Auto-Detection

Press <Enter> to autodetect the parameters of the SATA device on this channel.

IDE Channel 0, 1 Master/Slave

Configure your SATA devices by using one of the two methods below:

•

Auto

Lets the BIOS automatically detect SATA devices during the POST. (Default)

•

None

If no SATA devices are used, set this item to

None

so the system will skip

the detection of the device during the POST for faster system startup.

Access Mode

Sets the hard drive access mode. Options are: Auto (default), CHS, LBA, Large.

IDE Channel 2 Master/Slave

IDE Auto-Detection

Press <Enter> to autodetect the parameters of the SATA device on this channel.

Extended IDE Drive

Configure your SATA devices by using one of the two methods below:

•

Auto

Lets the BIOS automatically detect SATA devices during the POST. (Default)

•

None

If no SATA devices are used, set this item to

None

so the system will skip

the detection of the device during the POST for faster system startup.

Access Mode

Sets the hard drive access mode. Options are: Auto (default), Large.

The following fields display your hard drive specifications. If you wish to enter the parameters manually,

refer to the information on the hard drive.

2-4 Standard CMOS Features

Standard CMOS Features

Date (mm:dd:yy)

Wed,

Dec 22 2010

Time (hh:mm:ss)

22:31:24



IDE Channel 0 Master

[None]



IDE Channel 0 Slave

[None]



IDE Channel 1 Master

[None]



IDE Channel 1 Slave

[None]



IDE Channel 2 Master

[None]



IDE Channel 2 Slave

[None]

Halt On

[All, But Keyboard]

Base Memory

640K

Extended Memory

1022M

higf

: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

Item Help

Menu Level



Summary of Contents for GA-870A-USB3

































































































Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands

Gigabyte GA-870A-USB3, User Manual

Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands