Gigabyte GA-870A-USB3 User Manual Download

Page: 10 / 96

Hardware Installation

- 10 -

1-2 Product Specifications

CPU

Support for AM3 processors:

AMD Phenom™ II processor/ AMD Athlon™ II processor
(Go to GIGABYTE's website for the latest CPU support list.)

Hyper Transport
Bus

5200 MT/s

Chipset

North Bridge: AMD 870

South Bridge: AMD SB850

Memory

4 x 1.5V DDR3 DIMM sockets supporting up to 16 GB of system memory

* Due to Windows 32-bit operating system limitation, when more than 4 GB of physical

memory is installed, the actual memory size displayed will be less than 4 GB.

Dual channel memory architecture

Support for DDR3 2000(O.C.)/1333/1066 MHz memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory
modules.)

Audio

Realtek ALC889 codec

High Definition Audio

2/4/5.1/7.1-channel

Support for S/PDIF In/Out

Support for CD In

LAN

1 x Realtek RTL8111E chip (10/100/1000 Mbit)

Expansion Slots

1 x PCI Express x16 slot, running at x16 (PCIEX16)

* For optimum performance, if only one PCI Express graphics card is to be installed,

be sure to install it in the PCIEX16 slot.

1 x PCI Express x16 slot, running at x4 (PCIEX4)

2 x PCI Express x1 slots

(All PCI Express slots conform to PCI Express 2.0 standard.)
3 x PCI slots

Storage Interface

South Bridge:

- 6 x SATA 6Gb/s connectors supporting up to 6 SATA 6Gb/s devices

- Support for SATA RAID 0, RAID 1, RAID 5, RAID 10, and JBOD

USB

South Bridge:

- Up to 12 USB 2.0/1.1 ports (8 on the back panel, 4 via the USB brackets

connected to the internal USB headers)

Etron EJ168 chip:

- Up to 2 USB 3.0/2.0 ports

Summary of Contents for GA-870A-USB3

































































































Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands

Gigabyte GA-870A-USB3, User Manual

Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands