Gigabyte GA-870A-USB3 User Manual Download

Page: 20 / 96

Hardware Installation

- 20 -

In addition to the default speakers settings, the ~

audio jacks can be reconfigured to per

form different functions via the audio software. Only microphones still MUST be connected to
the default Mic in jack ( ). Refer to the instructions on setting up a 2/4/5.1/7.1-channel audio

configuration in Chapter 5, "Configuring 2/4/5.1/7.1-Channel Audio."

Center/Subwoofer Speaker Out Jack (Orange)

Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration.

Rear Speaker Out Jack (Black)

Use this audio jack to connect rear speakers in a 4/5.1/7.1-channel audio configuration.

Side Speaker Out Jack (Gray)

Use this audio jack to connect side speakers in a 7.1-channel audio configuration.

Line In Jack (Blue)

The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out Jack (Green)

The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be

used to connect front speakers in a 4/5.1/7.1-channel audio configuration.

Mic In Jack (Pink)

The default Mic in jack. Microphones must be connected to this jack.

Summary of Contents for GA-870A-USB3

































































































Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands

Gigabyte GA-870A-USB3, User Manual

Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands