Gigabyte GA-870A-USB3 User Manual Download

Page: 24 / 96

Hardware Installation

- 24 -

7) SATA3_0/1/2/3/4/5 (SATA 6Gb/s Connectors, Controlled by AMD SB850 South Bridge)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standards. Each SATA connector supports a single SATA device. The AMD SB850 controller

supports RAID 0, RAID 1, RAID 5, RAID 10, and JBOD. Refer to Chapter 5, "Configuring SATA Hard

Drive(s)," for instructions on configuring a RAID array.

•

A RAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard

drives are to be used, the total number of hard drives must be an even number.

•

A RAID 5 configuration requires at least three hard drives. (The total number of hard drives

does not have to be an even number.)

•

A RAID 10 configuration requires four hard drives.

SATA3_0

SATA3_1

SATA3_4

SATA3_3

SATA3_5

SATA3_2

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

Please connect the L-shaped end of

the SATA cable to your SATA hard

drive.

Pin No.

Definition

GND

TXP

TXN

GND

RXN

RXP

GND

Summary of Contents for GA-870A-USB3

































































































Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands

Gigabyte GA-870A-USB3, User Manual

Search results

Summary of Contents for GA-870A-USB3

Reviews:

Related manuals for GA-870A-USB3

Brands by name

Popular brands