Gigabyte E283-Z90-AAD1 User Manual Download Page 156

Page: 156 / 167

BIOS Setup

- 156 -

5-6-1 System Event Log

Parameter

Description

Enabling / Disabling Options

SEL Components

Change this item to enable or disable all features of System Event
Logging during boot.
Options available: Disabled, Enabled. Default setting is

Enabled

Erasing Settings

Erase SEL

Choose options for erasing SEL.
Options available: No/Yes, On next reset/Yes, On every reset. Default
setting is

When SEL is Full

Choose options for reactions to a full SEL.
Options available: Do Nothing, Erase Immediately. Default setting is

Nothing

Custom EFI Logging Options

Log EFI Status Codes

Enable/Disable the logging of EFI Status Codes (if not already converted
to legacy).
Options available: Disabled, Both, Error code, Progress code. Default
setting is

Error code

Summary of Contents for E283-Z90-AAD1








































































































































































Search results

Summary of Contents for E283-Z90-AAD1

Reviews:

Gigabyte E283-Z90-AAD1, User Manual, Page: 156 / 167

Search results

Summary of Contents for E283-Z90-AAD1

Reviews: