Gigabyte E283-Z90-AAD1 User Manual Download Page 114

Page: 114 / 167

BIOS Setup

- 114 -

Parameter

Description

ECC Configuration

Press [Enter] to configure advanced items.

DRAM ECC Symbol Size

–

Configures the DRAM ECC Symbol Size.

– Options available: Auto, x4, x8, x16. Default setting is

Auto

DRAM ECC Enable

– Enable/Disable DRAM ECC. When set to Auto, it will set ECC

to enable.

– Options available: Auto, Enabled, Disabled. Default setting is

Auto

DRAM UECC Retry

– Enable/Disable DRAM UECC Retry.

– Options available: Auto, Enabled, Disabled. Default setting is

Disabled

Max DRAM UECC Error Replay

(Note)

– Default setting is

Memory Clear

– Options available: Auto, Enabled, Disabled. Default setting is

Auto

Address XDR after ECC

– Options available: Auto, Enabled, Disabled. Default setting is

Disabled

(Note) This item available when

DRAM UECC Retry

is set to

Enabled

Summary of Contents for E283-Z90-AAD1








































































































































































Search results

Summary of Contents for E283-Z90-AAD1

Reviews:

Gigabyte E283-Z90-AAD1, User Manual, Page: 114 / 167

Search results

Summary of Contents for E283-Z90-AAD1

Reviews: