Gigabyte E283-Z90-AAD1 User Manual Download Page 112

Page: 112 / 167

BIOS Setup

- 112 -

Parameter

Description

Target Static Lane Select
Upper 32 bits

This item is configurable when

Target Static Lane Control

is set to

Enabled

Target Static Lane Select
Lower 32 bits

This item is configurable when

Target Static Lane Control

is set to

Enabled

Target Static Lane Select
ECC

This item is configurable when

Target Static Lane Control

is set to

Enabled

Target Static Lane Value

This item is configurable when

Target Static Lane Control

is set to

Enabled

Worst Case Margin
Granularity

Configures Worst Case Margin Granularity.

Options available: Per Chip Select, Per Nibble.
Default setting is

Worst Case Margin Only

Read Voltage Sweep Step
Size

Configures the step size for read Data Eye voltage sweep.

Options available: 1, 2, 4. Default setting is

Read Timing Sweep Step
Size

Configures the step size for read Data Eye timing sweep.

Options available: 1, 2, 4. Default setting is

Write Voltage Sweep Step

Configures the step size for write Data Eye voltage sweep.

Options available: 1, 2, 4. Default setting is

Write Timing Sweep Step
Size

Configures the step size for write Data Eye timing sweep.

Options available: 1, 2, 4. Default setting is

Silent Execution

Enable Mbist Target Static Lane Control.
Options available: Enabled, Disabled. Default setting is

Disabled

Summary of Contents for E283-Z90-AAD1








































































































































































Search results

Summary of Contents for E283-Z90-AAD1

Reviews:

Gigabyte E283-Z90-AAD1, User Manual, Page: 112 / 167

Search results

Summary of Contents for E283-Z90-AAD1

Reviews: