Gigabyte E283-Z90-AAD1 User Manual Download Page 111

Page: 111 / 167

BIOS Setup

- 111 -

5-3-3-3-1 Data Eye

Parameter

Description

Data Eye
Pattern Select

Options available: PRBS, SSO, Both. Default setting is

PRBS

Pattern Length

Determines the pattern length. The possible options are N=3....12.

Aggressor Channel

This item helps read the aggressors channels.
Options available: One Sub-Channel, Half Channels, All Channels. Default
setting is

All Channels

Aggressor Static Lane
Control

Enable/Disable the Aggressor Static Lane Control function.
Options available: Enabled, Disabled. Default setting is

Disabled

Aggressor Static Lane
Select Upper 32 bits

This item is configurable when

Aggressor Static Lane Control

is set to

Enabled

Aggressor Static Lane
Select Lower 32 bits

This item is configurable when

Aggressor Static Lane Control

is set to

Enabled

Aggressor Static Lane
Select ECC

This item is configurable when

Aggressor Static Lane Control

is set to

Enabled

Aggressor Static Lane
Value

This item is configurable when

Aggressor Static Lane Control

is set to

Enabled

Target Static Lane Control Enable/Disable the Target Static Lane Control function.

Options available: Enabled, Disabled. Default setting is

Disabled

Summary of Contents for E283-Z90-AAD1








































































































































































Search results

Summary of Contents for E283-Z90-AAD1

Reviews:

Gigabyte E283-Z90-AAD1, User Manual, Page: 111 / 167

Search results

Summary of Contents for E283-Z90-AAD1

Reviews: