Gigabyte E283-Z90-AAD1 User Manual Download Page 154

Page: 154 / 167

BIOS Setup

- 154 -

5-6 Server Management Menu

Parameter

Description

FRB-2 Timer

Enable/Disable FRB-2 timer (POST timer).
Default setting is

Enabled

FRB-2 Timer

timeout

Configures the FRB2 Timer timeout.

Options available: 3 minutes, 4 minutes, 5 minutes, 6 minutes. Default setting is

minutes

FRB-2 Timer Policy

Configures the FRB2 Timer policy.

Options available: Do Nothing, Reset, Power Down, Power Cycle.
Default setting is

Do Nothing

OS Watchdog
Timer

Enable/Disable OS Watchdog Timer function.
Options available: Enabled, Disabled. Default setting is

Disabled

OS Wtd Timer
Timeout

(Note)

Configures OS Watchdog Timer.

Options available: 5 minutes, 10 minutes, 15 minutes, 20 minutes.
Default setting is

10 minutes

OS Wtd Timer
Policy

(Note)

Configure OS Watchdog Timer Policy.

Options available: Do Nothing, Reset, Power Down, Power Cycle.
Default setting is

Reset

Wait BMC Ready

Post wait BMC ready and reboot system.
Options available: Disabled, 2 minutes, 4 minutes, 6 minutes. Default setting is

minutes

(Note) This item

is configurable when

OS Watchdog Timer

is set to

Enabled

Summary of Contents for E283-Z90-AAD1








































































































































































Search results

Summary of Contents for E283-Z90-AAD1

Reviews:

Gigabyte E283-Z90-AAD1, User Manual, Page: 154 / 167

Search results

Summary of Contents for E283-Z90-AAD1

Reviews: