Gigabyte E283-Z90-AAD1 User Manual Download Page 103

Page: 103 / 167

BIOS Setup

- 103 -

5-3-3 UMC Common Options

Parameter

Description

UMC Common Options
DDR4 Addressing Options

Press [Enter] for configuration of advanced items.

DDR Controller Configuration Press [Enter] for configuration of advanced items.

DDR MBIST Options

Press [Enter] for configuration of advanced items.

DDR RAS

Press [Enter] for configuration of advanced items.

DDR Bus Configuration

Press [Enter] for configuration of advanced items.

DDR Timing Configuration

Press [Enter] for configuration of advanced items.

DDR Training Options

Press [Enter] for configuration of advanced items.

DDR Security

Press [Enter] for configuration of advanced items.

DDR PMIC Configuration

Press [Enter] for configuration of advanced items.

DDR Miscellaneous

Press [Enter] for configuration of advanced items.

Summary of Contents for E283-Z90-AAD1








































































































































































Search results

Summary of Contents for E283-Z90-AAD1

Reviews:

Gigabyte E283-Z90-AAD1, User Manual, Page: 103 / 167

Search results

Summary of Contents for E283-Z90-AAD1

Reviews: