Gifas-electric CircLED Installation Instructions Manual Download Page 17 | Manualshive

Page: 17 / 22

background image

TrafficLED / CircLED

Seite 17 / 22

Created

15.06.2015

chal

Modified

04.10.2017

roen

Object-ID

989827

Alignment procedure

Hint

Loosen the 4 screws of the alignment ring on the in-
stallation box only slightly!

Place the alignment guide (fit the screw heads into the
slots) and turn the alignment ring into the desired posi-
tion.

Remove the guide carefully and tighten the 4 screws.

Preparing the cables/strands

Pull the cable loop from the installation box and cut it
so that 2 pieces of cable of about 15cm remain. Strip
the cable up to about 5cm from the threaded cable
gland.

«
...
15
16
17
18
19
...
»

Summary of Contents for CircLED























Reviews:

No comments

Related manuals for CircLED

Brand: ABB Pages: 370

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: Radio Shack Pages: 52

Brand: Nelson Pages: 19

Brand: C-TEC Pages: 2

Brand: Hamworthy Pages: 10

Brand: GE Pages: 8

Brand: GARAN Pages: 8

Brand: Gamma Vacuum Pages: 25

Brand: Gamma Pages: 28

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands