Gifas-electric CircLED Installation Instructions Manual Download Page 13 | Manualshive

Page: 13 / 22

background image

TrafficLED / CircLED

Seite 13 / 22

Created

15.06.2015

chal

Modified

04.10.2017

roen

Object-ID

989827

Installation conditions Traffic-/CircLED with leveling support

4.1 Selecting the levelling range

-

The levelling console can be used for

2 different height adjustment ranges

.

Adjustment range:

-

TrafficLED 85-113mm

-

CircLED 74-102 mm

Place the retaining plate, with the brackets facing

up

,

on the black marking light base.

Adjustment range:

-

TrafficLED 113-168mm

-

CircLED 102-157mm

Place the retaining plate, with the brackets facing

down

,

on the black marking light base.

Ring of CircLED not present

«
...
11
12
13
14
15
...
»

Summary of Contents for CircLED























Reviews:

No comments

Related manuals for CircLED

Brand: Walchem Pages: 10

Brand: QUAD Pages: 16

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

Brand: Federal Signal Corporation Pages: 34

Brand: Jäger Pages: 50

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: Rabe Pages: 61

Brand: Racal Instruments Pages: 35

Brand: Monster Central Pages: 13

Brand: Rain Bird Pages: 18

Brand: GEM Pages: 17

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Controller CR100

Brand: Sonos Pages: 2

Brand: McIntosh Pages: 68

Universal Family for Sony

Brand: Jolly Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands