GiBiDi AS05800, Instructions For Installation Manual

Page: 21 / 56

20 21
SC380 SC380
UK UK
3 - INSTALLATION WARNINGS
Ÿ
protexion degree of the case.
Ÿ
Before proceeding with the installation, it is necessary to fit a magnetothermal and differential switch with a
maximum capacity of 10A upstrem of the system. The switch must guarantee an omnipolar separation of the
contacts, with an opening distance of at least 3 mm.
Ÿ
To prevent possible interference, differentiate and always keep the power cables (minimum section 1,5mm²)
separate from the signal cables (minimum section 0,5mm²).
Ÿ
Make the connections referring to this manual. Connect in series all the devices that must be connected to the
same N.C. (normally closed) input and in parallel all the devices that share the same N.O. (normally open) input.
Incorrect installation or improper use of the product may compromise the safety of the system.
Ÿ
Keep all the matrials contained in the packaging away from children, since they pose a potential risk.
Ÿ
The manufacturer declines all responsibility for improper functioning of the automated device, if the original
components and accessories, suitable for the specific automation, are not used.
Ÿ
At the end of the istallation, always check carefully the proper functioning of the system and the devices used.
Ÿ
This instruction manual addresses people qualified for the installation of “live equipment”. Therefore good
technical knowledge and professional practice in compliance with the regulations in force are required.
Ÿ
Maintenance must be carried out by qualified personnel.
Ÿ
Before carrying out any cleaning or maintenance operation, disconnect the control unit from the mains.
Ÿ
This control unit may only be used for the purpose for which it was designed.
Ÿ
The use of the product for purposes different from the intended use has not been tested by the manufacturer.
Therefore any work is carried out on full responsibility of the installer.
Ÿ
Mark the automated gate with visible warning plates.
Ÿ
Warn the user that children or animals may not play or stand around near the gate.
Ÿ
Appropriately protect the dangerous points (for example, use one or more sensitive edges).
Use suitable cable glands to assure the correct mechanical connection of the wiring and maintain the Ip55
4 - WARNINGS FOR THE USER
Ÿ
In the event of an operating fault or failure, cut the power upstream of the control unit and call the Technical Service.
Ÿ
Periodically check the functioning of the safety devices. Any repair must be carried out by specialised personnel
using original and certified materials.
Ÿ
The appliance is not to be used by children or people with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction.
Ÿ
Do not access to the electronic board for adjustments and/ or maintenance
WARNING: IMPORTANT SAFETY INSTRUCTIONS.
It is very important to follow these instructions for your own safety.
Please keep this instruction manual.
5 - ELECTRICAL CONNECTIONS: TRANSFORMER
Faston
Fig.
Cable colour Description
J1 Brown
Primary 380 Vac transformer
J2
Grey
Primariy 230 Vac transformer
J3
Black
Primary 0 Vac transformer
J4 3
Red Secondary 14 Vac transformer
J5
J6
Blue Secondary 22 Vac transformer
J7
6 - ELECTRICAL CONNECTIONS: TERMINAL BOARDS
Terminal
Fig.
Position Description
1
Ground wire connection
9
Signal
GND
2
M1
3
4 M2
5
Motor
Motor connection
Motor connection
Motor connection
10
6
7
M3 Lamp
230 Vac 40 W flashing light output
13
11
12
(Menu C2)
8
9
M4
REL1
Menu 32
Free contact (NO)
14
(Menu E 32)
10
11
M5
REL2
Menu 34
Free contact (NO)
15
(Menu E 34)
12
230 Vac / 380 Vac power supply input
R
13 S
14 T
M6
6
7
8