Ghost Controls DTP1 Page 50 Installation And Owner'S Manual Download

Page: 50 / 68

P U S H - T O - O P E N

A. DIP SWITCH OPTION Settings. There are four DIP Switches located on the main control board (shown) that

must be positioned properly for your particular installation.

B. DIP #1 OPEN DIRECTION. The opening direction of the gate operator is determined by DIP#1.

DIP Switch # OFF Position

ON Position

Pull-To-Open (Factor y

Default): Gate is pulled to open

into your property.

Push-To-Open Installation: Gate is pushed to open away from your

property.

C. DIP #2 ALARM WARNING. The warning alarm is determined by DIP#2.

DIP Switch # OFF Position

ON Position

Warning Disabled:

AUTOCLOSE and initial gate

movement alarm warning is dis-

abled. This does not disable the

alarm warning for consecu-

tive obstruction as required by

UL325 safety standard.

Warning Enabled (Factory Default): AUTOCLOSE and initial gate

movement warning is enabled.

D. DIP #3 MONITORED SAFETY DEVICES. The mode of the monitored safety setting for the system is

determined by DIP#3. When using monitored external safety devices (such as monitored photo eyes), move

DIP Switch #3 to monitored safety mode.

UNIT WILL NOT OPERATE IN MONITORED SAFETY MODE WITHOUT MONITORED EXTERNAL SAFETY

DEVICES PRESENT, CONNECTED, AND POWERED ON.

DIP Switch # OFF Position

ON Position

Patent-pending

SafeForce®

Mode (Factory Default): Force

output is limited to ensure safe

operation as specified by Type

C in UL325 requirement.

Monitored Safety Mode: Monitored safety devices required /

Compatible GHOST CONTROLS

safety devices only. Monitored

safety devices must be present and operate properly as specified by

Type B1 or B2 in UL325 requirement. See monitored safety device

connection in the monitored photo eye instructions manual for more

details.

Summary of Contents for DTP1





































































Search results

Summary of Contents for DTP1

Reviews:

Related manuals for DTP1

Brands by name

Popular brands

Ghost Controls DTP1, Installation And Owner'S Manual

Search results

Summary of Contents for DTP1

Reviews:

Related manuals for DTP1

Brands by name

Popular brands