Ghost Controls DTP1 Installation And Owner'S Manual Download

Page: 13 / 68

S Y S T E M O V E R V I E W

This gate operator is only intended for use on gates

intended for vehicular access and is not intended for

pedestrian gate applications. Pedestrians must use a

separate entrance.

The GHOST CONTROLS

Automatic Gate Opener

can be installed on a pull-to-open application with the

items included in the kit. For push-to-open applica-

tions you will need to purchase the required Push-To-

Open (item AXPO) bracket kit from your local retailer

or visit

https://www.ghostcontrols.com/shop

or contact

GHOST CONTROLS

Sales at 850-558-5520 to

purchase.

This GHOST CONTROLS

Automatic Gate Opener

features a patent-pending SafeForce

power limiting

feature that doesn’t require Photo Eyes for entrapment

protection in most applications of a properly installed

gate. During installation, you may instead choose to use

external monitored safety devices such as non-contact

photo eyes (item AXPE sold separately) and will need

to enable this setting on the main system controller

during setup.

The operator can be used on a variety of gate types,

but

CAN NOT BE USED ON SOLID OR WOOD

PANEL GATES. Solid panel gates have a higher

resistance to wind and may result in damage to the

automatic gate operator.

All GHOST CONTROLS

Automatic Gate Operators

include automatic reversing safety features that will

make the gates stop and reverse direction within 2 sec-

onds of encountering an obstruction. There is a manual

setting on the main gate operator control board labeled

Force Setting that adjusts the sensitivity of this feature.

This GHOST CONTROLS

Automatic Gate

Operator can be enhanced with additional GHOST

CONTROLS

accessories such as our remote

transmitters, keypads, and all other accessories,

sold separately. (Accessories see page 66). The

GHOST CONTROLS

technical support team is

happy to assist in verifying compatibility of any products

not offered by GHOST CONTROLS

. For additional

assistance, please contact GHOST CONTROLS

Technical support

https://myghostcontrols.force.com/

Support/s

or by calling 850-898-1411.

Check all local building codes and ordinances prior to

installing this automatic gate operator system to make

sure your planned installation is in compliance.

Your gate must be in good working condition before

installation of the automatic gate operator system and

meet the following criteria:

GATE CAN NOT USE WHEELS for support or

drag along the ground at any point in the opening

or closing cycle.

GATE SHOULD BE LEVEL, PLUMB, AND

MOVE FREELY IN BOTH DIRECTIONS

WHEN MINIMAL FORCE IS APPLIED IN

THE OPENING OR CLOSING DIRECTION.

Gate should NOT open uphill or downhill.

The vehicular entry gate system must be installed

in a location that prevents entrapment by providing

sufficient clearance between it and adjacent structures

when opening and closing.

SYSTEM OVERVIEW

IMPORTANT INSTRUCTIONS

Thank you for choosing a GHOST CONTROLS

Automatic Gate Opener system, the most innovative gate opener systems

available for residential applications on the market today. This manual will guide you through the proper installation and main-

tenance methods. To reduce the risk of injury or death:

READ, UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS

CAREFULLY AND COMPLETELY. Following these directions is critical to a successful and safe operating environment.

Summary of Contents for DTP1





































































Search results

Summary of Contents for DTP1

Reviews:

Related manuals for DTP1

Brands by name

Popular brands

Ghost Controls DTP1, Installation And Owner'S Manual

Search results

Summary of Contents for DTP1

Reviews:

Related manuals for DTP1

Brands by name

Popular brands