Ghost Controls DTP1 Installation And Owner'S Manual Download

Page: 29 / 68

P U L L - T O - O P E N

PREPARING THE GATE SYSTEM CONTROLLER

The gate system control board provides one convenient place to make all of your system connections and to change any

settings that you desire to personalize how your automatic gate opener system operates at your home or property. This main

board (shown below) is located inside of the control box of your system and will be referred to in detail through the next few

sections. Because this control box may be mounted within reach of children or potential vandals, we offer and recommend an

operator lock security kit (AX2L) as an accessory to safely lock this box in the closed position to prevent tampering.

NOTE:

BEFORE PROCEEDING MAKE SURE THE ON/OFF SWITCH ON BOTTOM OF CONTROL BOX IS IN THE

OFF POSITION.

STEP 10.

Check the system DIP switch settings and verify in the correct positions as shown.

DIP Switch # OFF Position

ON Position



Factory Default:

Pull-To-Open



Push-To-Open



Warning Disabled



Factory Default: Warning Enabled



Factory Default:

SafeForce

Mode



Monitored External Safety Devices Mode



Factory Default:

Delay Open 2nd Arm



Simultaneous Open

Summary of Contents for DTP1





































































Search results

Summary of Contents for DTP1

Reviews:

Related manuals for DTP1

Brands by name

Popular brands

Ghost Controls DTP1, Installation And Owner'S Manual

Search results

Summary of Contents for DTP1

Reviews:

Related manuals for DTP1

Brands by name

Popular brands