Gevril GV2 Series Manual Download

Page: 49 / 54

Rubber Strap

When adjusting the length of the strap, the clasp should be set

in its shortest position.

Measure the circumference of the wrist by using the flexible

measure, placing the blank end over the graduated part.

Remove the spring pins from the steel clasp by pushing them

in.

Cut off the two lengths below the figure corresponding to the

number indicated on the flexible measure when the wrist

was measured. If there is any doubt as to the exact measure-

ment, it is preferable to cut at the upper graduation.

Insert the two spring pins in the holes of the rubber strap.

Insert the rubber sections with the spring pins fitted into the

steel clasp by pushing in the two spring pins. The side

marked GV2 should face opposite to the skin.

Rubber Strap

CLOSING

Press the flap marked GV2 gently; a click sound confirms the

flap is locked. Then press the flap marked G gently; a click

sound confirms the flap is locked.

Rubber Strap

When adjusting the length of the strap, the clasp should be set

in its shortest position.

Measure the circumference of the wrist by using the flexible

measure, placing the blank end over the graduated part.

Remove the spring pins from the steel clasp by pushing them

in.

Cut off the two lengths below the figure corresponding to the

number indicated on the flexible measure when the wrist

was measured. If there is any doubt as to the exact measure-

ment, it is preferable to cut at the upper graduation.

Insert the two spring pins in the holes of the rubber strap.

Insert the rubber sections with the spring pins fitted into the

steel clasp by pushing in the two spring pins. The side

marked GV2 should face opposite to the skin.

Rubber Strap

CLOSING

Press the flap marked GV2 gently; a click sound confirms the

flap is locked. Then press the flap marked G gently; a click

sound confirms the flap is locked.

Rubber Strap

When adjusting the length of the strap, the clasp should be set

in its shortest position.

Measure the circumference of the wrist by using the flexible

measure, placing the blank end over the graduated part.

Remove the spring pins from the steel clasp by pushing them

in.

Cut off the two lengths below the figure corresponding to the

number indicated on the flexible measure when the wrist

was measured. If there is any doubt as to the exact measure-

ment, it is preferable to cut at the upper graduation.

Insert the two spring pins in the holes of the rubber strap.

Insert the rubber sections with the spring pins fitted into the

steel clasp by pushing in the two spring pins. The side

marked GV2 should face opposite to the skin.

Rubber Strap

CLOSING

Press the flap marked GV2 gently; a click sound confirms the

flap is locked. Then press the flap marked G gently; a click

sound confirms the flap is locked.

RUBB

TRAP

Insert the two spring pins in the

holes of the rubber strap.

Insert the rubber sections with

the spring pins fitted into the

steel clasp by pushing in the two

spring pins. The side marked GV2

should face opposite to the skin.

ClOSING

Press the flap marked GV2 gently; a click sound confirms the flap is

locked. Then press the flap marked G gently; a click sound confirms

the flap is locked.

Summary of Contents for GV2 Series























































Search results

Summary of Contents for GV2 Series

Reviews:

Related manuals for GV2 Series

Brands by name

Popular brands

Gevril GV2 Series, Manual

Search results

Summary of Contents for GV2 Series

Reviews:

Related manuals for GV2 Series

Brands by name

Popular brands