DEUTSCH
Störung
Mögliche Ursachen
Lösung
Wenn das Lernverfahren gestartet wird�
blinkt die LED SET UP� aber die Automation
bewirkt keine Bewegung
Die Sicherheitseinrichtungen STOP und FSW sind auch
während des Lernverfahrens aktiv� Wenn sie gar nicht
oder unsachgemäß angeschlossen sind� wird die
Funktionstüchtigkeit des Antriebs gehemmt
Den Status der LED kontrollieren und hierzu
die Angaben der Tabelle „Anzeige-LED
der Eingänge” beachten� Die in Abb� ��
aufgeführten Anschlüsse überprüfen
Die Automation bewirkt gar keine
Bewegung
Der STOP-Impuls ist aktiv
Die Automation öffnet das Tor� schließt
es aber nicht wieder
Die Sicherheitseinrichtungen FSW sind
belegt
D i e F a i l s a f e - F u n k t i o n i s t a k t i v �
aber der Ruhekontakt der an den FSW-Eingang
angeschlossenen Vorrichtungen öffnet sich während
des vom Steuergerät vor dem Start der Bewegung
ausgeführten Tests nicht
Das Lernverfahren wird nicht korrekt
abgeschlossen und das Blinken der LED
SET UP signalisiert eine Störung
Die Automation steuert häufige
Umkehrungen der Bewegungsrichtung
beim Öffnen und/oder beim Schließen
- Die Automation erfasst eine übermäßige
Bewegungsschwierigkeit des Tors
- Bei der manuellen Krafteinstellung
könnte die eingestellte Kraft nicht
ausreichend sein�
Den Ausgleich des Tors überprüfen und
sicherstellen� dass das Tor sich ohne
ü b e r m ä ß i g e R e i b u n g e n b e w e g t �
D a s To r m i t d e r H a n d b e w e g e n
u n d h i e r z u d i e V e r b i n d u n g
der Stange auf dem Tor verwenden
und sicherstellen� dass die Bewegung
reibungslos ist und keine übermäßige
Zug- oder Schubkraft erfordert� Ein neues
Lernzyklus durchführen� Eventuell die Schubkraft
ändern (bei manueller Einstellung)
oder eine neue Lernphase mit ma��
Schubkraft von 1000N starten�
Die Entriegelung der Automation ist
schwierig bei geschlossenem Tor
Die mechanische Belastung des
Entriegelungssystems bei geschlossenem
Tor ist zu hoch
Ein neues Lernverfahren starten und nach
Abschluss des Verfahrens die Schubkraft beim
Schließen erleichtern und das Zurückfahren
des Schlittens entsprechend der Beschreibung
in Abschnitt 11�� steuern�
Die LED SET UP blinkt und signalisiert eine
Störung
Das Lernverfahren wurde nicht erfolgreich
abgeschlossen
Ein neues Lernverfahren ausführen
18
. HINWEISE ZUR LÖSUNG VON PROBLEMEN
Der Schalter Nr� 3 von DS1 (automatische
/manuelle Krafteinstellung) wurde
verschoben und ein neues Lernzyklus wurde
nicht durchgeführt�
Summary of Contents for ZODIAC 100
