Genie Z-51/30J Service And Repair Manual Download Page 87

Page: 87 / 144

October 2020

Part No. 1268553GT

Z®-51/

31J

Service and Repair Manual

Deutz TD 2.2 L3 Engine Fault Codes

DTC = Diagnostic Trouble Code
FMI = Failure Mode Identifier
SPN = Suspect Parameter Number

DTC

SPN

FMI Description

1000 98

Engine oil level sensor internal
error. Sensor reports error. Open/
short transducer.

1001 98

Engine oil level out of range. Level
low, high, foaming.

1002 98

Oil sensor voltage out of range.
<8,5V ±0,5V; >16,5V ±0,5V.

1003 98

Oil sensor invalid sensor status.

1004 98

Oil sensor temperature out of
range.

1005 98

Oil sensor is broken or
disconnected.

1021 100

Oil pressure voltage above normal
or shorted to high.

1022 100

Oil pressure voltage below normal
or shorted to low.

1025 100

Low oil pressure. Warning
threshold exceeded.

1026 100

Low oil pressure. Shut off
threshold exceeded.

1043 107

Air filter differential pressure. Air
filter clogged.

1071 411

Engine exhaust gas recirculation.
Pressure does not change
between engine operating points.

1072 411

Engine exhaust gas recirculation.
Pressure above normal operational
range.

1073 411

Engine exhaust gas recirculation.
Pressure below normal operational
range.

1074 411

Engine exhaust gas recirculation.
Negative measured differential
pressure.

1075 411

Engine exhaust gas recirculation.
Positive measured differential
pressure.

DTC

SPN

FMI Description

1077 411

Engine exhaust gas recirculation.
Signal value above maximum limit.

1078 411

Engine exhaust gas recirculation.
Signal value below maximum limit.

1079 108

Ambient air pressure sensor above
normal operational range.

1080 108

Ambient air pressure sensor below
normal operational range.

1081 108

Fault check max signal range
violated for ambient air pressure
sensor.

1082 108

Fault check min signal range
violated for ambient air pressure
sensor.

1083 108

Ambient air pressure sensor error
by component self diagnosis.

1084 3720

DPF ash load above normal
operational range.

1086 3734

DPF soot load exceeded. Remove
filter level.

1087 4781

DPF soot load exceeded shut off
level.

1088 4781

DPF soot load exceeded warning
level.

1089 4781

DPF. Too much standstill time in
short time interval.

1090 10156

DPF. The standstill-regeneration
mode time exceeds the short-limit.

Summary of Contents for Z-51/30J

















































































































































Search results

Summary of Contents for Z-51/30J

Reviews:

Related manuals for Z-51/30J

Brands by name

Popular brands

Genie Z-51/30J, Service And Repair Manual

Search results

Summary of Contents for Z-51/30J

Reviews:

Related manuals for Z-51/30J

Brands by name

Popular brands