General International MS3002 Setup & Operation Manual Download Page 14

Page: 14 / 52

MS3002 Manual v.200909

Page 14

3. If the tool suddenly stalls while

cutting wood, release the trigger

switch, unplug the tool, and free the

blade from the wood. The saw may

now be started and the cut finished.

4. FUSES

may “blow” or circuit

breakers may trip frequently if:

a. MOTOR

is overloaded –

overloading can occur if you

feed too rapidly or make too

many start/stops in a short time.

b. LINE VOLTAGE

is more

than 10% above or below the

nameplate voltage rating. For

heavy loads, the voltage at

motor terminals must equal

the voltage specified on the

nameplate.

c. IMPROPER

or dull saw blades

are used.

5. Most motor troubles may be traced

to loose or incorrect connections,

overload, low voltage or inadequate

power supply wiring. Always check

the connections, the load and supply

circuit if the motor doesn’t run well.

Check minimum gauge for the length

of cord you are using on the chart

below.

GUIDELINES FOR

EXTENSION CORDS

Use a proper extension cord. Make sure

your extension cord is in good condition.

When using an extension cord, be

sure to use one heavy enough to carry

the current your product will draw. An

undersized cord will cause a drop in

line voltage, resulting in loss of power

and cause overheating. The table below

shows the correct size to use depending

on cord length and nameplate ampere

rating. If in doubt, use the next heavier

gauge. The smaller the gauge number,

the heavier the cord.

Be sure your extension cord is

properly wired

and in good condition.

Always replace a damaged extension

cord or have it repaired by a qualified

person before using it. Protect your

extension cords from sharp objects,

excessive heat and damp or wet areas.

Use a separate electrical circuit for

your tools.

This circuit must not be less

than a #18 wire with a 9 A time lag fuse.

NOTE: When using an extension cord on

a circuit with a #18 wire, the extension

cord must not exceed 25 feet in length.

Before connecting the tool to the power

line, make sure the switch is in the OFF

position and the electric current is rated

the same as the current stamped on the

motor nameplate, running at a lower

voltage will damage the motor.

In all cases make certain the

receptacle in question is properly

grounded. If you are not sure, have

a certified electrician check the

receptacle.

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

(When using 120 volts only)

Ampere Rating

Total length of Cord

More Than Not More Than 25ft. 50ft. 100ft. 150ft.
0 6

18 16 16 14

6 10

18 16 14 12

10 12

16 16 14 12

12 16

14 12 Not Recommended

ELECTRICAL REQUIREMENTS AND SAFETY

Summary of Contents for MS3002





















































Search results

Summary of Contents for MS3002

Reviews:

Related manuals for MS3002

Brands by name

Popular brands

General International MS3002, Setup & Operation Manual

Search results

Summary of Contents for MS3002

Reviews:

Related manuals for MS3002

Brands by name

Popular brands