manualshive.com logo in svg

General DataComm Xedge 6000 Series, Hardware Installation

Share
Download
General DataComm Xedge 6000 Series Hardware Installation Download Page 131

Line Interface Modules

Serial I/O (SI-2C/SI-4C) LIM Overview

032R440-000

Xedge 6000 Hardware

5-29

Issue 17

Installation & Setup Guide

Serial I/O (SI-2C/SI-4C) LIM Overview

The SI-2C and the SI-4C LIMs have 2- or 4-port serial interfaces and are 
intended for use with a variety of controllers as listed in 

Table 1-4

.

Front Panel Indicators

Two LEDs per link indicate In Service (IS) and LoopBack (LB). 

•

IS 

(In Service) LED illuminates when the LIM controller has 

finished configuring the LIM, and the associated link is in service. 

•

LB 

(Loopback) LED illuminates during a digital, link or line 

loopback.

SI-2C/SI-4C LIM Cabling

Table 5-10

 lists cables by interface and DTE/DCE mode of operation.

DCE/DTE Configuration

The SI-2C or SI-4C LIM must be properly configured for DCE or DTE 
operation on all links before installation in the Xedge chassis. When 
shipped from the factory in

 DCE mode

, the resistor packs for each link 

are positioned in the default DCE Port socket locations, as shown in 

Figure 5-17

.

If your application requires the LIM is configured for DTE mode, you 
must perform the following steps for each link:

1. Move the 16-pin resistor pack from the

 DCE PORT 0 

socket to 

the adjacent empty DTE socket labeled

 DTE PORT 0

. 

2. Move the 16-pin resistor pack from the

 DCE PORT 1 

socket to 

the adjacent empty DTE socket labeled

 DTE PORT 1

. 

Note

IMPORTANT! The resister packs are the only 16-pin DIP (Dual Inline Package) on the board. Use care when 
removing and installing the resistor packs. Do not bend or break the pins.

Table 5-10

Cable Compatibility

GDC Part 

Number

Cable for Connecting EIA/TIA Alt A to:

027H444-005

RS449 DTE

027H445-005

RS449 DCE

027H442-005

EIA/TIA530 DCE

027H443-005

EIA/TIA530 DTE

027H446-005

V.35 DCE

027H447-005

V.35 DTE

027H440-005

X21 DCE

027H441-005

X21 DTE

L0

IS

LB

L1

LINK 0

LINK 1

SI-2C

L0

IS

LB

L1

IS

LB

L2

L3

LINK 0

LINK 1

LINK 2

LINK 3

SI-4C

Summary of Contents for Xedge 6000 Series































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands