Generac Power Systems MLT6SMD Owner'S Manual Download Page 9 | Manualshive

Page: 9 / 60

background image

Introduction and Safety

Owner’s Manual for MLT6SMD Light Tower

5

Operating Safety

Positioning the Unit

•

If the unit is equipped with a frame grounding stud,
follow any local, state, and National Electrical Code
(NEC) guidelines when connecting.

Starting the Unit

Raising and Lowering the Mast

•

Keep area around the unit clear of people while
raising and lowering the mast.

•

ALWAYS

lower the mast when not in use.

(000260a)

High Voltage. Verify area above unit is clear
of overhead wires and obstructions. Contact
with high-voltage power lines will result in
death or serious injury.

DANGER

(000147)

WARNING

Risk of Fire. Unit must be positioned in a
manner that prevents combustible material
accumulation underneath. Failure to do so
could result in death or serious injury.

(000250)

WARNING

Equipment and property damage. Do not operate unit on
uneven surfaces, or areas of excessive moisture, dirt, dust
or corrosive vapors. Doing so could result in death, serious
injury, property and equipment damage.

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

CAUTION

(000291)

Equipment damage. Do not attempt to start or operate
a unit in need of repair or scheduled maintenance.
Doing so could result in serious injury, death, or
equipment failure or damage.

WARNING

(000277)

WARNING

Burn hazard. Never operate lights with a
damaged or missing lens cover. Lamps are
hot and pressurized while in use. Unprotected
lamps can shatter, causing severe injury.

WARNING

Electrocution. Do not set up or operate
this unit if severe weather is expected.
Lightning strikes can kill or cause severe injury
even if you are not touching the unit.

(000296)

WARNING

(000297)

> 60 mph

> 60 mph

Do not set up the unit if high winds
are expected. High winds can cause the
unit to tip or fall, causing severe injury
or machine damage.

WARNING

Personal Injury. Stop immediately if the mast hangs
up or the winch cable develops slack. Excess slack
could cause the mast to collapse, resulting in personal
injury or equipment damage.

(000265)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit
before raising the mast. Keep the outriggers extended while
the mast is up. Failure to do so could cause the unit to tip
and fall and could result in death or serious injury.

WARNING

Burn Hazard. Allow bulb fixture to cool 10-15
minutes before handling or lowering mast.
Failure to do so could result in serious injury.

(000358)

«
...
7
8
9
10
11
...
»

Summary of Contents for MLT6SMD





























































Reviews:

No comments

Related manuals for MLT6SMD

ACS880-01 Series

Brand: ABB Pages: 238

Brand: Taylor Made Pages: 2

Brand: York Fitness Pages: 18

Brand: Safco Pages: 2

Brand: Omni Pages: 193

Brand: Bacharach Pages: 48

Brand: GE Pages: 212

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brand: YASKAWA Pages: 40

RAISED GARDEN BED

Brand: Yardfully Pages: 2

Brand: 4iQ Pages: 6

PowerGen 5650 Series

Brand: Qnergy Pages: 10

Brand: Wayflex Pages: 11

Brand: FOSCARINI Pages: 16

Brand: ABB Pages: 154

Brand: Metrohm Pages: 42

Brand: Maquet Pages: 232

KONTROL KUBE ABACUS

Brand: FIBERLOCK Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands