Generac Power Systems MLT6SMD Owner'S Manual Download Page 8 | Manualshive

Page: 8 / 60

background image

Introduction and Safety

4

Owner’s Manual for MLT6SMD Light Tower

Fuel Hazards

•

DO NOT

operate with the fuel tank cap loose or

missing.

Engine Safety

Internal combustion engines present special hazards
during operation and fueling. Failure to follow the safety
guidelines described below could result in severe injury or
death. Read and follow all safety alerts described in the
engine operator's manual. A copy of this manual was
supplied with the unit when it was shipped from the factory.

•

DO NOT

run engine indoors or in an area with poor

ventilation. Verify engine exhaust cannot seep into
closed rooms or ventilation equipment.

•

Shut the engine down if any of the following
conditions exist during operation:
• Abnormal change in engine speed.
• Loss of electrical output.
• Equipment connected to the unit overheats.
• Sparking occurs.
• Engine misfires or there is excessive engine/

generator vibration.

• Protective covers are loose or missing.
• Ambient air temperature is above 120 °F (49 °C).

(000192)

DANGER

Explosion and fire. Fuel and vapors are extremely
flammable and explosive. No leakage of fuel is
permitted. Keep fire and spark away. Failure to do
so will result in death or serious injury.

(000168)

DANGER

Explosion and Fire. Fuel and vapors are
extremely flammable and explosive. Keep fire
and spark away. Failure to do so will result
in death or serious injury.

(000174)

DANGER

Risk of fire. Allow fuel spills to completely dry
before starting engine. Failure to do so will
result in death or serious injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are
extremely flammable and explosive. Add fuel
in a well ventilated area. Keep fire and spark
away. Failure to do so will result in death
or serious injury.

Asphyxiation. Running engines produce
carbon monoxide, a colorless, odorless,
poisonous gas. Carbon monoxide, if not
avoided, will result in death or serious injury.

(000103)

DANGER

DANGER

Asphyxiation. Do not operate unit without
a properly functioning exhaust system.
Doing so will result in death or serious injury.

(000340)

WARNING

Fire risk. Fuel and vapors are extremely
flammable. Do not operate indoors. Doing so
could result in death, serious injury, or
property or equipment damage.

(000281)

Risk of fire. Never operate engine without
the air cleaner installed. Operating engine
without the air cleaner could result in death
or serious injury.

WARNING

(000249)

WARNING

Explosion and Fire. Do not smoke while
refueling unit. Failure to do so could result in
death, serious injury, or property or equipment
damage.

(000284a)

CAUTION

(000317)

Equipment damage. Do not clean air filter elements.
Contaminants may remain after cleaning, shortening
air filter service life. Doing so could result in engine or
equipment damage.

«
...
6
7
8
9
10
...
»

Summary of Contents for MLT6SMD





























































Reviews:

No comments

Related manuals for MLT6SMD

Brand: ABB Pages: 14

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

Brand: Faderfox Pages: 8

Brand: M-Audio Pages: 25

Brand: U-Line Pages: 3

Brand: U-Line Pages: 2

Brand: NAMYSLO Pages: 13

McDonnell & Miller PSE-800-M

Brand: Xylem Pages: 20

Brand: Hammer Strength Pages: 8

Brand: Econo-Wrap Pages: 27

Brand: JONATHAN Y Pages: 2

RGB-BNTv2 NTV-KIT903

Brand: Nav TV Pages: 6

Brand: jcb Pages: 2

PORTABLE ANALOGUE AUDIO TAPE RECORDER

Brand: Nagra Pages: 64

Brand: Resvent Pages: 42

Brand: B meters Pages: 8

rina 8304301012

Brand: LUTEC Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands