manualshive.com logo in svg

Generac Power Systems MLT6SMD, Owner'S Manual

Share
Download
Generac Power Systems MLT6SMD Owner'S Manual Download Page 20

General Information

16

Owner’s Manual for MLT6SMD Light Tower

Place Trailer Tongue in Storage Position

1.

Verify unit is on a level surface and wheels are 
blocked.

2.

See 

Figure 2-6

. Extend jack (A) enough to allow

minimum effort to pivot trailer tongue into storage
position.

Figure 2-6. Extend Jack and Remove Pins

3.

Remove pins (B) and (C) from trailer tongue.

4.

See 

Figure 2-7

. Pivot trailer tongue into storage

position.

NOTE: 

Varying levels of effort may be required

depending on terrain.

Figure 2-7. Pivot Trailer Tongue Into Storage Position

5.

See 

Figure 2-8

. Install pins (B) and (C) at locations

shown to secure trailer tongue in storage position.

Figure 2-8. Install Pins and Rotate Jack

6.

Remove clevis and remove jack (A) from tongue
weldment.

7.

Completely retract jack.

8.

Rotate jack 90° counterclockwise, place jack on
tongue weldment, and install clevis to secure jack
parallel to ground.

003593

A

B

C

CAUTION

(000313)

Pinching and crushing hazard. To avoid
possible injury, keep fingers away from pivot 
point when folding or unfolding trailer tongue.  

003520

003591

A

B

C

Summary of Contents for MLT6SMD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands