manualshive.com logo in svg

Generac Power Systems MLT6SMD, Owner'S Manual

Share
Download
Generac Power Systems MLT6SMD Owner'S Manual Download Page 35

Operation

Owner’s Manual for MLT6SMD Light Tower

31

3.

Rotate the mast by loosening the mast rotation
knob (B) at the bottom of the mast. Turn the mast
until the lights face in the desired direction, and
then tighten the mast rotation knob to secure the
mast in position.

4.

Use the winch (C) to slowly extend the mast. Verify
the coiled electrical cord is extending at the top
sections of the mast. STOP extending the mast
when the colored mark (D) on the second mast
section is visible as seen in Detail D.

IMPORTANT NOTE: Contact a GMP ASD immedi-
ately if the mast hangs up or the winch cable devel-
ops slack.

Raising the Mast—Electric Winch 

(If Equipped) 

1.

Set up and level the unit. See 

Light Tower Setup

.

2.

See 

Figure 3-3

. Inspect the mast cables for

excessive wear or damage. Verify the cables are
properly centered in each pulley (A). Inspect the
electrical cord for damage.

Figure 3-3. Switch & Pulley Locations - Electric 

Winch

3.

Rotate the mast by loosening the mast rotation
knob at the bottom of the mast (D). Turn the mast
until the lights face in the desired direction and
then tighten the mast rotation knob to secure the
mast in position.

4.

Press and hold the winch control switch (Detail B)
upward to telescope the mast to the desired height.
Verify that the coiled electrical cord is extending at
the top sections of the mast. STOP extending the
mast when the colored mark (C) on the second mast
section is visible as seen in Detail C.

IMPORTANT NOTE: A limit switch on the main mast
section will disconnect power to the upper electric
winch to prevent overextending the mast.

WARNING

Tipping hazard. Do not extend the mast beyond the 
colored mark on the second mast section. The unit 
can become unstable and tip or fall, causing injury.

(000262)

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

WARNING

(000266)

Tipping hazard. Extend the outriggers and level the unit 
before raising the mast. Keep the outriggers extended while 
the mast is up. Failure to do so could cause the unit to tip 
and fall and could result in death or serious injury. 

DETAIL C

STOP

DETAIL B

D

B

C

A

006439

Summary of Contents for MLT6SMD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands