manualshive.com logo in svg

Generac Power Systems MLT6SMD, Owner'S Manual

Share
Download
Generac Power Systems MLT6SMD Owner'S Manual Download Page 46

Maintenance

42

Owner’s Manual for MLT6SMD Light Tower

Winch Mechanical Brake

The mechanical brake generates heat when loads are
lowered and the wire cable is powered out. Care must be
taken to avoid overheating the mechanical brake.
Whine or chatter associated with a new mechanical
brake is normal and typically disappears with use.

Overheating the mechanical brake may result in
permanent damage to, or failure of, the brake. Replace
any damaged brake components before resuming use of
the winch.

Trailer Wheel Bearings

The trailer axles are

 

equipped with a Zerk grease fitting

to allow lubrication of the wheel bearings without the
need to disassemble the axle hub. Use only a high
quality grease made specifically for lubrication of wheel
bearings, such as Valvoline

®

 W615 or equivalent.

Proceed as follows to lubricate the wheel bearings:

1.

See 

Figure 4-2

. Remove the small rubber plug (A)

from the metal end cap (B).

Figure 4-2. Wheel Bearing Cross Section

2.

Attach a standard grease gun fitting to the Zerk
grease fitting (C).

3.

Pump grease into the Zerk fitting until fresh grease
is visible around the nozzle of the grease gun.

4.

Wipe any excess grease from the axle hub with a
clean cloth and install the rubber plug.

The minimum recommended lubrication is every 12
months or 12,000 mi (19,312 km). More frequent
lubrication may be required under extremely dusty or
damp operating conditions.
Every six months, or depending on usage, inspect for
play in each bearing by jacking up the trailer, then trying
to rock the wheel. If further assistance is required, con-
tact Generac Mobile Products Technical Service at 1-
800-926-9768.

Jack Maintenance

Inspect each jack foot before each use for damage and
remove any mud or debris. The jacks must be clean and
in good operating condition to properly support the unit.

Maintenance Activity

After First 

Operation

Before Each 

Use

Semi-Annually

Inspect fasteners

Inspect electrical connections

Inspect condition of cables

Clean and grease brake assembly

Inspect motor brushes

Inspect winch and control

002540

B

C

A

Summary of Contents for MLT6SMD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands