Gemtek WX-1516 User Manual Download Page 47

Page: 47 / 52

5.8 Upgrading the Access Point firmware

You can upgrade the firmware in the Access Point. New firmware

versions may become available to add features to the Access Point

or to solve problems.

The following procedure assumes the new firmware is already

present on your computer.

To upgrade the firmware:

1. Make sure the firmware version you are about to install is

newer than the version currently running on the Access Point:

on the

Identity

page, check the firmware version.

2. Click the

firmware upgrader

link at the top of the browser

window. A new window opens.

3. Click Browse to browse to the new firmware file.

4. Click Upgrade.

The upgrade process begins. This may take a few minutes.

Do not switch off the power from the Access Point while the

upgrade is in progress.

Summary of Contents for WX-1516





















































Search results

Summary of Contents for WX-1516

Reviews:

Related manuals for WX-1516

Brands by name

Popular brands

Gemtek WX-1516, User Manual

Search results

Summary of Contents for WX-1516

Reviews:

Related manuals for WX-1516

Brands by name

Popular brands