Gemini GEM-P816 Page 28 Installation Instructions Manual Download

Page: 28 / 60

GEM-P816 Installation Instructions

NAPCO Security Systems

WI994C 3/04

Page 26

KEYPAD MESSAGES

The GEM-RP1CAe2/GEM-K1CA Keypads can display the below messages. The GEM-RP2ASe2/GEM-K2AS will display similar
abbreviated messages that may scroll through two screens.

Note:

See page 7 for a listing of the keypad specific User Guides avail-

able. These User Guides contain more details regarding the various keypad messages.

SYSTEM READY

- All zones operating; system can be armed. 1

through 2 = Area.

ARMING YYY/XXX SECONDS

- Exit delay in progress. XXX = exit

time remaining in 10-second decrements; YYY = AWAY or
STAY. Arming then becomes ARMED.

DISARM NOW/XXX SECONDS

- Entry delay in progress. XXX =

entry time remaining in 10-second decrements.

SYSTEM ARMED

- Panel armed. GEM-RP1CAe2/GEM-K1CA key-

pads only.

ZONE FAULTED

- One or more zones not secured. Display status

for zone description(s). GEM-RP1CAe2/GEM-K1CA only.

CAN'T ARM SYSTEM/ZONE FAULTED

- Arming attempted with

Priority Zone in trouble. Secure zone to arm.

DAY ZONE TROUBLE

- Trouble condition on Day Zone, followed by

one or more zone descriptions.

INVALID ENTRY/TRY AGAIN

- Wrong code/time/area number

entered.

CAN'T ARM SYSTEM/PRESS RESET KEY

- Arming attempted with

System Trouble present. Press the

button and then arm

the system.

ALARM

- Alarm condition, followed by one or more zone

descriptions.

FIRE ALARM

- Alarm condition on a Fire Zone. Enter your code

then press the

button to silence the sounder. Correct the

cause of the alarm, then press the

button again. Fire

alarm condition, followed by one or more zone descriptions.

SYSTEM TROUBLE

- A System Trouble display will be followed by

one or more of the following error codes:

AC POWER FAIL/E01-00 SERVICE.

Power failure. Check

power transformer. Check for blown fuse or circuit breaker;
general power outage.

LOW BATTERY/E02-00 SERVICE.

Battery below 11 volts. If not

recharged within 24 hours, replace it.

COMM FAIL/E03-00 SERVICE.

Unsuccessful communication to

central station.

Note:

Will also display if panel improperly

programmed to report; i.e., Report Alarm, Report Codes,
Subscriber ID Numbers, etc. must be programmed.

WIRELESS TROUBLE/04-NN SERVICE.

Wireless transmitter

supervisory failure. NN = transmitter number.

WIRELESS LOWBATT/E05-NN SERVICE.

Rf transmitter low

battery. NN = transmitter number.

SYSTEM TROUBLE/E06-NN SERVICE.

Rf receiver response

trouble. NN = receiver number.

SYSTEM TROUBLE/E07-00 SERVICE.

Download failure.

SYSTEM TROUBLE/E08-00 SERVICE.

Telephone line failure

(system trouble displays after a fixed 60 second delay).

SYSTEM TROUBLE/E09-00 SERVICE, NO PANEL PROGRAM.

System cold start not programmed after address 1198.

SYSTEM TROUBLE/E10-NN SERVICE.

Keypad response

failure. NN = keypad number.

SYSTEM TROUBLE/E11-NN SERVICE.

Keypad tamper cover

removed. NN = keypad number.

SYSTEM TROUBLE/E12-NN SERVICE.

Expansion zone module

failure. NN = module number.

SYSTEM TROUBLE/E13-NN SERVICE.

EZM module cover

removed. NN = module number.

SYSTEM TROUBLE/E14-NN SERVICE.

Relay board response

failure. NN = relay board number.

SYSTEM TROUBLE/E15-NN SERVICE.

Wireless transmitter

tamper cover removed. NN = transmitter number.

SYSTEM TROUBLE/E16-NN SERVICE.

Receiver jammed. NN

= receiver number.

SYSTEM TROUBLE/E17-NN SERVICE.

Receiver cover

removed. NN = receiver number.

SYSTEM TROUBLE/E18-NN SERVICE.

Key fob RF transmitter

low battery. NN = key fob transmitter number.

SYSTEM TROUBLE/E19-00 SERVICE.

Internal user memory

error. Select RESET SYSTEM TBL. Press the

button,

then the

button.

SYSTEM TROUBLE/E20-00 SERVICE.

Internal dealer memory

error.

SYSTEM TROUBLE/E21-NN SERVICE.

Check GEM-Printer

Module, printer out of paper or printer off-line.

SYSTEM TROUBLE/E22-NN SERVICE.

No trip detected on PIR

Supervision Zone within programmed Sensor-Watch time. NN
= Zone number. To reset, press NEXT/YES button at “

RESET

SENSOR MSG

” function display.

SYSTEM TROUBLE/E23-00 SERVICE.

Failure of 4-wire bus.

Check Terminals 11/12.

SYSTEM TROUBLE/E27-00 SERVICE.

Printer Failure. Call in-

stalling company for service.

SYSTEM TROUBLE/E39-00 SERVICE.

Receiver capacity error.

SYSTEM TROUBLE/E40-00 SERVICE.

RF Self-Test failure.

SYSTEM TROUBLE/E41-NN SERVICE

. Trouble condition on a

Fire Zone. Press

button to silence the sounder.

Correct the trouble, then press the

button again.

(GEM-P1632 and GEM-P816 panels only).

SYSTEM TROUBLE/E51-00 SERVICE

- Alarm Output

Supervisory.

SYSTEM TROUBLE/E58-00 SERVICE.

Telemetry Trouble. Call

installing company for service.

SYSTEM TROUBLE/E59-00 SERVICE.

Telemetry Failure. Call

installing company for service.

SYSTEM TROUBLE/E66-00 SERVICE. "

Clean Me" warning--

Smoke Detector dirty. Clean detector or call installing com-
pany for service.

SYSTEM TROUBLE/E99-00 SERVICE.

Keypad Panic shorted

too long (RP2/K2 and RP3/K3 keypads).

NN OUT OF SYSTEM

- Keypad inoperative. NN = keypad

number.

FAULT FIND/RF SIGNAL POWER

- Fault-find Mode activated.

Message

Summary of Contents for GEM-P816





























































Search results

Summary of Contents for GEM-P816

Reviews:

Related manuals for GEM-P816

Brands by name

Popular brands

Gemini GEM-P816, Installation Instructions Manual

Search results

Summary of Contents for GEM-P816

Reviews:

Related manuals for GEM-P816

Brands by name

Popular brands