X
GEM-P816 Installation Instructions
L
NAPCO Security Systems
WI994C 3/04
!
Page 32
Dealer Security Code
The factory-programmed Dealer Security Code is “456789”. Use this code to enter the Easy Menu Driven Mode (Dealer Program
Mode) to program (or change) the Dealer Security Code. The Dealer Security Code is needed to enter the Dealer Program Mode, thus
allowing the dealer to program codes, zone features, reporting features and zone descriptions. This code should be changed as
required.
Dial-Tone Detection; Disable Auto Dial-Tone Detection
The panel features automatic dial-tone detection to ensure that a dial tone is present before the communicator dials. To disable this
feature, program an “8” in Location 0394.
When an “E” is programmed before the first digit of an outside telephone number, the communicator dial-tone detection circuit is set to
detect the standard 440Hz dial tone. The “E” is generally entered in the location immediately preceding the telephone number.
It may be necessary to program at least one 4-second pre-dial delay before a dial-tone detection “E”. With certain nonstandard
exchanges, pre-dial delay “D”s may be used without a dial-tone detection “E”. (See Access Number for Outside Line; Pre-Dial Delay;
Telephone Numbers.)
Digital Dialer Report Enter/Exit Test Mode
(SIA CP-01 Requirement: 4.6.4.2)
Initiation Report
. At the initiation of a test, the control panel sends a message to the central station that a test is in progress. The "Fault
Find" function (a Function Menu selection) is enabled, and normally causes all zones to give a two second beep at the keypad(s) when
any zone is faulted or restored. As required by SIA CP-01, Fault Find is expanded with the following features when
Digital Dialer Re-
port Enter/Exit Test Mode
is programmed. This option is programmed when "Enable CP-01 Feature" is selected in the Easy Program
Menu:
•
When Fault Find is entered, it reports to Central Station that "Test Mode" is in progress. On completion of the report, a Ring-Back will
be given.
•
Fault Find can not be initiated from an armed panel, and all digital dialer reporting is inhibited while in Fault Find.
•
Fault Find Central Station Reporting Code is located at address 0350.
•
Keypad will display the following warning that the system is in Fault Find: "FAULT FIND RF SIG POWER - - "
•
If 24-hour zone is open at end of test, no report is sent (GEM-P816). If a 24-hour zone is tripped and not restored during Fault Find,
when the mode is exited the zone will display as "Faulted" on the keypad display.
•
When Fault Find is exited by pressing
C
, a Fault Find Restore Report will be sent, and upon completion of the report a Ring-
Back will be given.
Disable Call Waiting (Touch-tone® Dialing Only)
A digital communicator connected to a telephone line with Call Waiting may be disrupted by this feature. However, most lines with Call
Waiting also have Selective Call Waiting, which permits the feature to be turned off by dialing a “*70” just before the telephone number.
A “*” will be dialed by programming a “B”.
If the installation has the Call Waiting feature, be sure that it also has Selective Call Waiting, and confirm the disable code with the
telephone company. Then program this code (“B70”) directly before the phone numbers (after dial-tone detection or pre-dial delay) in
the telephone-number locations. See Telephone Numbers.
Caution:
Should the user cancel his Call Waiting service, the communicator will dial a wrong number unless the phone number is
corrected.
Disable Call Waiting on 1
st
Attempt
(Address 1062, Bit 5)
Cancel "*70" after the 1
st
dial attempt. Default is disabled. When enabled, this option will dial the Central Station telephone number as
it is programmed in the panel. If the first communication is unsuccessful, the next and remaining dial attempts will remove the
*
star
button (entered as a "B" from the keypad) and the 2 subsequent digits from the Central Station telephone number.
Disable Callback Download
See Callback-Method Download
Disable Code Required for Easy Bypass. See Selective Bypass
Disable Function-Mode Download
See Callback-Method Download
Disable Openings/Closings
Provides the flexibility of disabling openings and/or closings for any area(s).
Disable Handshake on Xmit (All Formats)
Causes data transmission to wait one second after dialing a pager telephone number before sending data.
Disable PGM2 Clear on Disarm
PGM2 will not clear when a user code is entered to disarm.
Disable System Trouble Audible Timeout
If the trouble occurs when disarmed, the sounder will now automatically time out in 10 minutes, without the need to press [RESET].
Must be selected in UL Installations.
Glossar
y
