manualshive.com logo in svg

Gema PH300, Operating Instructions And Spare Parts List

Share
Download
Gema PH300 Operating Instructions And Spare Parts List Download Page 3

 

Rev. 00  01/22 

 

PH300 

Table of contents  

•

  3 

 

Table of contents 

About these instructions 

5

 

General information ................................................................................................ 5

 

Keeping the Manual ................................................................................................ 5

 

Safety symbols (pictograms) ................................................................................... 5

 

Presentation of the contents ................................................................................... 6

 

Figure references in the text ...................................................................... 6

 

Safety 

7

 

General information ................................................................................................ 7

 

Basic safety instructions ......................................................................................... 7

 

Product specific security regulations ...................................................................... 8

 

Product description 

9

 

Intended use ........................................................................................................... 9

 

Reasonably foreseeable misuse .............................................................. 10

 

Structure ................................................................................................................ 10

 

Overall view.............................................................................................. 10

 

Compressed air indicators .................................................................................... 11

 

Feed Control Hood ................................................................................................ 11

 

Principle of operation ............................................................................................ 12

 

Technical Data ...................................................................................................... 12

 

Powder transport ...................................................................................... 12

 

Electrical data .......................................................................................... 12

 

Pneumatic data ........................................................................................ 13

 

Dimensions .............................................................................................. 13

 

Processible powders ................................................................................ 13

 

Sound pressure level ............................................................................... 13

 

Rating plate .............................................................................................. 14

 

Additional equipment / options .............................................................................. 14

 

Assembly / Connection 

15

 

Set-up .................................................................................................................... 15

 

Connecting the powder hopper ............................................................................. 15

 

Connecting the supply .......................................................................................... 15

 

Connecting the electrics ........................................................................... 15

 

Connecting the pneumatic system ........................................................... 16

 

Grounding of the fresh powder hopper ................................................................. 16

 

Start-up 

17

 

Cleaning the interior of the powder hopper ........................................................... 17

 

Filling the powder hopper ...................................................................................... 17

 

Setting the fluidization .............................................................................. 18

 

Start-up inspection ................................................................................................ 19

 

Operation 

21

 

Safety .................................................................................................................... 21

 

Summary of Contents for PH300







































Reviews:

No comments

Brands by name

Popular brands

Load more brands