Geist cool ClosetAir Installation Manual Download Page 16 | Manualshive

Page: 16 / 53

background image

ClosetAir Installation Manual

16

© 2017 Geist

GM1159 ClosetAir Installation Manual

Chapter 2 - Pre-Installation

The RAC10 relies on the building installation for protection from overcurrent. A Listed circuit breaker
is required in the building installation. The circuit breaker should be rated at 15 or 20 Amps. Install
the RAC10 so the input plug may be disconnected for service.

Installation:

1.

Using appropriate hardware, mount unit into wall or dropped ceiling as detailed in the Mounting
Requirements Section of Instruction Manual.

2.

Plug RAC10 into appropriately rated and protected branch circuit receptacle.

Service and Maintenance:

No service or maintenance is required. Do not attempt to open the RAC10 or you may void the
warranty. No serviceable parts inside.

«
...
14
15
16
17
18
...
»

Summary of Contents for ClosetAir






















































Reviews:

No comments

Related manuals for ClosetAir

Brand: True Pages: 2

Brand: Smeg Pages: 14

Brand: AEG Pages: 40

Brand: AEG Pages: 12

Brand: AEG Pages: 32

ARCTIS 2150-7 GS

Brand: AEG Pages: 32

Brand: Tricity Bendix Pages: 20

Brand: JUNO Pages: 9

Brand: Fagor Pages: 76

Brand: Fagor Pages: 76

Brand: Fagor Pages: 52

Brand: Rieber Pages: 51

Brand: Danby Pages: 10

Brand: Bartscher Pages: 21

BlueCool Truck BCT010300A

Brand: Webasto Pages: 54

Brand: IceManCooler Pages: 2

Brand: Pando Pages: 124

Brand: Zero Appliances Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands