gefran ADL300 EPC v2 User Manual Download Page 30

Page: 30 / 64

____________________ _

ADL300-EPCv2- User Guide

Page 30 of 64

Setting of the jerk value for the initial part of deceleration.

Maximum deceleration value setting.

Setting of the jerk value for the final part of deceleration.

Setting of the acceleration coefficient multiplier.

If set to 100 the ramp uses the coefficients entered in the parameters.

If set to a value of less than 100 the lift will accelerate over a longer distance.

If set to a value of more than 100 the lift will accelerate over a shorter distance.

Setting of the deceleration coefficient multiplier.

If set to 100 the ramp uses the coefficients entered in the parameters.

If set to a value of less than 100 the lift will decelerate over a longer distance.

If set to a value of more than 100 the lift will decelerate over a shorter distance.

05.04 – SEQUENCES

This menu contains the parameters used to manage and define the travel of the lift according to the status of

the inputs and alarms. The structure of the lift sequences in case of a floor call command is summarised

below. Once the command has been received and the number of the floor to be reached has been saved,

the internal positioning device starts and automatically executes the trajectory until reaching the floor with

direct arrival.

In case of jog speed the deceleration sequence starts the moment the jog command is removed.

Starting sequence:

1. Reading of the Enable hardware input and alarm check (enabling is interrupted if any alarms are

present)

Recognition of the

Enable

and

Floor Call

commands as set in

Seq start mode

3. Upon receiving the

Floor Call

command, the number of the floor to be reached is acquired by

reading the binary combination of the Floor0, Floor1, Floor 2… bits as a function of the direction of

travel. A command is sent to close the contactors

After the time set

Contactor close delay

the internal

Enable

signal is activated

5. The system waits for the magnetisation signal from the drive (

Drive Ready

)

6. After magnetisation the signal is activated to release the brake

7. The system waits for the brake to be released (

Contactor Open Delay

)

8. After the brake release delay the

Lift Start

command is sent and the movement is enabled.

Menu

Par

Description

Type

FB BIT

Def

Min

Max

Acc

Mod

5.3.4 11014

Dec ini jerk

m/s3

FLOAT

1.400

0.001

FVS

Menu

Par

Description

Type

FB BIT

Def

Min

Max

Acc

Mod

5.3.5 11016

Deceleration

m/s2

FLOAT

0.600

0.001

FVS

Menu

Par

Description

Type

FB BIT

Def

Min

Max

Acc

Mod

5.3.6 11018

Dec end Jerk

m/s3

FLOAT

0.500

0.001

FVS

Menu

Par

Description

Type

FB BIT

Def

Min

Max

Acc

Mod

5.3.7 13184

PercAccFactor

Perc

FLOAT

100.0

0.0

1000.0

FVS

Menu

Par

Description

Type

FB BIT

Def

Min

Max

Acc

Mod

5.3.8 13186

Perc Dec Factor

Perc

FLOAT

100.0

0.0

1000.0

FVS

Summary of Contents for ADL300 EPC v2

































































Search results

Summary of Contents for ADL300 EPC v2

Reviews:

gefran ADL300 EPC v2, User Manual, Page: 30 / 64

Search results

Summary of Contents for ADL300 EPC v2

Reviews: