Gecko Aeware 3 in.clear, User Instructions And Functions

Page: 10 / 25

19 18
in.clear in.clear
•The cell is installed after the heater in the circulation pump line.
• The appliance must be installed in a location that is inaccessible
to a person in the bath or spa and must be located or fixed so
that it cannot fall into the bath or spa.
• The appliance is not intended for submersion but may be
installed within the spa zone.
• A means for disconnection must be incorporated in the fixed
wiring in accordance with the wiring rules.
• To reduce the risk of injury, do not allow children to operate
this device.
• It is the responsibility of the user to test the spa water regularly
to ensure that adequate amounts of bromine are generated to
achieve proper sanitizer levels.
• Heavy spa usage may require higher bromine output to maintain
proper free available bromine residuals.
• Maintaining overly high Sodium Bromide and bromine levels
above recommended range can contribute to corrosion of spa
equipment and may damage components of the spa.
• Do NOT use any ozone or UV sanitizer.
Warnings!
Important safety instructions
• Check the expiry date of the test kit as test results may be
inaccurate if used after that date.
• Follow all aspects of the local and National Electrical Code(s)
when installing the in.clear™ Automatic Bromine Generator.
• People with a medical condition should consult a physician
before entering spa water.
• Women who are pregnant should NOT enter the spa.
• Maximum spa water usage temperature is 40°C. Bathing in spa
water at 40°C should not exceed 15 minutes.
• For proper sanitation, Spas must be completely drained
periodically. The number of days between COMPLETE SPA
DRAINAGE is equal to the volume of the Spas water in liters,
divided by 10 times the maximum number of daily spa users.
Refill spa with water and repeat DIRECTION FOR USE of the
device.
- For a 1500 liters (400 US gallons) spa used by 2 adults twice a
week: 1500 / (10 x (4/7)) = 262 days or 8 months
• In.clear™ is meant for a covered spa NOT swimming pools.
• Users should always shower before entering a spa.
warnings
Warnings!
Important safety instructions
• For Canada, in.clear™ must only be used with Sodium Bromide
(such as BromiCharge™) scheduled or registered under the Pest
Control Product Act. For USA, the Sodium Bromide (such as
BromiCharge™) must be registered under EPA.
• Read and follow this manual carefully and make sure to save it
for later.
• This manual contains important information on in.clear's
installation, use and safety recommendations. It is your
responsibility to install and use your in.clear™ unit safely.
• In.clear™ must be connected to a circuit protected by a ground
fault interrupter device (GFCI) in North America or residual
current device (RCD) having a rated residual operating current
not exceeding 30 mA in Europe.
• Make sure all electrical power is off before installing the in.clear™
unit. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
• Use only an electrical cord in good conditions to power
in.clear™.
• Always clean or replace your filter cartridges at regular intervals,
otherwise part of the bromine generated by in.clear™ will only
serve to oxidize the dirt accumulated in the filter.
• Do NOT add any other sanitation chemicals in the spa other than
registered Sodium Bromide (such as BromiCharge™)
• Operating the in.clear™ at reduced Sodium Bromide (such as
BromiCharge™) levels will shorten the life of the cell.
• Do not open the in.clear™ unit; there are no serviceable parts
inside.
• Disposal of the product: the in.clear™ unit must be disposed
of separately in accordance with the local waste disposal
legislation in force.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• To reduce the risk of injury, do not allow children to operate this
device.
• In.clear™ may not be suitable for in ground spas, it may affect
some materials used in their construction.
warnings