Gebruder Heyl Analysentechnik Testomat 2000 DUO Operating Instructions Manual Download Page 10

Page: 10 / 54

Installation

Installation

Risks resulting from incorrect installation!



Install Testomat 2000

DUO at a location where it is protected

against dripping or splash water, dust and aggressive substances
– e. g. in a switch cabinet or on a suitable wall.

Information for trouble-free operation



Install Testomat 2000

DUO vertically and without mechanical

stress.



Install Testomat 2000

DUO

at a vibration-free site.

Operating Testomat 2000

DUO in the pres-

sure range 0.3 to 1 bar

Prior to installation, please check whether lower operating pressure is
required. The instrument is factory set for the operating range 1 to 8

bar. Remove the flow controller valve body

to operate the instru-

ment in the operating range 0.3 to 1 bar (e.g. when using an aerator

type R). This involves removing the retaining pin

from the control-

ler / filter receiver

. Subsequently use the metal bracket to remove

the controller plug

from the borehole. Subsequently remove the

flow controller valve body

and reinsert the controller plug and the

retaining pin.

Installing Testomat 2000

DUO

Select an installation site where the water inlet hose can be kept as
short as possible (max. 5 m).



Please leave sufficient space on the left-hand side of the instru-

ment to open the door.



Drill the mounting holes as shown in the drawing on the left.



Use three screws to attach the instrument at a suitable position in

the switch cabinet or on a wall.

NOTE

Remove for
pressure
range 0.3 to 1
bar

WARNING

Summary of Contents for Testomat 2000 DUO























































Search results

Summary of Contents for Testomat 2000 DUO

Reviews:

Related manuals for Testomat 2000 DUO

Brands by name

Popular brands

Gebruder Heyl Analysentechnik Testomat 2000 DUO, Operating Instructions Manual

Search results

Summary of Contents for Testomat 2000 DUO

Reviews:

Related manuals for Testomat 2000 DUO

Brands by name

Popular brands