GE Profile Owner'S Manual And Installation Instructions Download

Page: 30 / 46

MEASURE CABINET OPENING

AVAILABLE VS. REFRIGERATOR WIDTH

Measure width of cabinet opening where

refrigerator will be placed, W.
Be sure to account for any countertop overhang,

baseboard thickness and any clearance desired.

Width, W, should not be less than 36”. The

refrigerator will be placed approximately in the

middle of this opening.

MATERIALS YOU MAY NEED

(not included)

TOOLS YOU WILL NEED

Pencil

1/8” (3 mm) Drill Bit and

Electric or Hand Drill

Tape measure

5/16” (8 mm) Nut Driver

Lag Bolts
1/4” (6 mm) x 1-1/2” (38 mm)

Anchor Sleeves

1/2” (12 mm) OD

For Anti-Tip Bracket Mounted on CONCRETE Floors Only

Drill Bit Appropriate for Anchors

AT-1

Baseboard
Thickness or
Countertop
Overhang
(Whichever Is
Larger) Plus
Any Desired
Clearance

Rear Wall

Front

RH Side

AT-2

LOCATING THE ANTI-TIP FLOOR

BRACKET

Place the anti-tip floor bracket locator template

(included inside the anti-tip kit) onto the floor

up against the rear wall, within W, and in line

with the desired location of the RH side of the

refrigerator (see Figure 1).

Place the anti-tip floor bracket onto the locator

template with its RH floor holes lined up with

the floor holes indicated on the template sheet,

approximately 15 ¼” from the edge of the sheet

or the RH side of the refrigerator.
Hold down in position and use the anti-tip floor

bracket as a template for marking the holes

based upon your configuration and type of

construction as shown in Step 3. Mark the hole

locations with a pencil, nail or awl.
NOTE:
• It is REQUIRED to use at least 2 screws to mount

the floor bracket (one on each side of the

anti-tip floor bracket). Both must be into either

the wall or the floor. Figure 2 indicates all the

acceptable mounting configurations for screws.

Identify the screw holes on the anti-tip floor

bracket for your configuration.

REFRIGERATOR

Figure 1 – Installation Overview

Base Bracket

on the

Refrigerator

2 Wall Holes

RH Side of

Refrigerator

Floor – Concrete

(2 Holes)

Floor – Wood

(2 Holes)

15 ¼”

Locator Template

Sheet

Floor Bracket

to Install

RH Holes

Rear RH

Corner of

Cabinet Wall

NOTE:

If you did not receive an anti-tip bracket with your

purchase, call 1.800.626.8774 to receive one at no

cost. (In Canada, call 1.800.561.3344.)

For installation instructions of the bracket, visit: www.

GEAppliances.com.

(In Canada, www.GEAppliances.ca.)

Installation

Anti-Tip Floor Bracket

Instructions

WARNING

Tip Over Hazard.

Built-in style models (model PYE, CYE, GYE, PWE, CWE,

and ZWE) are top heavy, especially with any doors

open. These models must be secured with the anti-tip

floor bracket to prevent tipping forward, which could

result in death or serious injury. Read and follow

the entire installation instructions for installing the

anti-tip floor bracket packed with your refrigerator.

PYE, CYE, GYE, PWE, CWE,

and ZWE Models Only

Refer to 239D1142P001, Pub No. 31-45484-5

Summary of Contents for Profile















































Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands

GE Profile, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands