GE Profile Page 22 Owner'S Manual And Installation Instructions Download

Page: 22 / 46

TOOLS YOU MAY NEED

Installation

Refrigerator

Instructions

GE and GE Profile™ models

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at: www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

Tip Over Hazard.

Built-in style models (model PYE, CYE, GYE, PWE,

CWE, and ZWE) are top heavy, especially with any doors

open. These models must be secured with the anti-tip

floor bracket to prevent tipping forward, which could

result in death or serious injury. Read and follow the entire

installation instructions for installing the anti-tip floor

bracket packed with your refrigerator.
•

IMPORTANT

³ Observe all governing codes and

ordinances. Save these instructions for local inspector’s use.

•

Note to Installer – Be sure to leave these instructions with

the Consumer.

• Note to Consumer – Keep these instructions for future

reference.

• Skill level – Installation of this appliance requires basic

mechanical skills.

• Completion time –

Refrigerator Installation can vary

Water Line Installation 30 minutes

• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered

under the Warranty.

PREPARATION

MOVING THE REFRIGERATOR INDOORS
If the refrigerator will not fit through a doorway,

the refrigerator door and freezer drawer can be removed.
• To remove the refrigerator door, see the Installing

the Refrigerator section.

• To remove the freezer drawer, see the Removing

the Freezer Drawer section.

WATER SUPPLY TO THE ICE MAKER AND DISPENSER
If the refrigerator has an ice maker, it will have to be

connected to a cold water line. A GE water supply kit

(containing tubing, shutoff valve, fittings and instructions)

is available at extra cost from your dealer, by visiting

our website at GEAppliances.com (in Canada at www.

GEAppliances.ca) or from Parts and Accessories, 800.626.2002

(in Canada 1.800.661.1616).

Adjustable Wrench

1/4” Outer Diameter

Compression Nut

and Ferrule (sleeve)

Phillips-Head Screwdriver

Ȓµ

Socket Ratchet/Driver

1/8”, 3/32”, 1/4” & 5/32”

Allen Wrenches

Pencil

1/8” Drill Bit and

Electric or Hand Drill

Tape Measure

1/4” Nut Driver

5/16” Nut Driver

Pliers

Level

Flat-Head Screwdriver

Torx T20, T25

Summary of Contents for Profile















































Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands

GE Profile, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands