GE Profile Page 26 Owner'S Manual And Installation Instructions Download

Page: 26 / 46

REINSTALLING THE REFRIGERATOR DOORS

Reverse steps 1 through 4 to reinstall refrigerator, follow

details below for critical alignments.

Reinstall center hinge first and torque the screws to 65

in-lbs. With the LH door at 90º to the front of

the case, lower the refrigerator door onto the center hinge.

Ensure that the door and hinge align correctly.

Rotate doors closed and make sure moveable center sealing

portion of the door aligns with the striker. If the door will not

self-close after reinstalling, remove door, turn door upside

down, check alignment mark and arrow; (there is an

alignment mark on the door closure mechanism. It

corresponds to an alignment arrow on the plastic ring.

Rotate door closure mechanism to align mark and arrow,

reinstall door).

Securely tape the door shut with masking tape or have a

second person support the door. Reinstall the top hinge and

torque the screws to 65 in-lbs.

Be sure to reinstall the ground wire and strain relief to the top

hinge.

Reinstall hinge cover. NOTE: Ensure wires are not pinched or

under screw bosses before tightening screws.

REMOVE THE REFRIGERATOR DOORS (cont)

Note: for proper installation later, please follow the next step

carefully.

Remove the tape and keeping the door as

straight as possible, open the door to 90º then lift

straight up to remove it.

REMOVE OPPOSITE DOOR

Follow the same procedure on the opposite door. There

are no wires or water lines on the opposite side

4 REMOVE CENTER HINGE (if necessary)

Remove the 3/8

screws securing the center hinge to the

cabinet.

Use T20 driver to remove outboard screw

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

Remove

center screw

Lift up & off
center hinge

Open Door to 90°

Align flats with tab.

Underside OF
Fresh Food Door

If door cannot be installed at 90° follow steps below:

1. Install door at 180° to case front.

2. If space limits opening door to less than 180°, then:

a) Remove door, carefully turn door upside down.

b) Check alignment of door closure mechanism shaft

on underside of door. The flats on the shaft should

correspond to alignment tab on plastic ring or

mark on bottom end cap.

c) If shaft is not aligned to tab/mark, using 5/32” Allen

wrench, rotate door closure mechanism shaft

counterclockwise for right door and clockwise for

left door. Then align flat with tab/mark.

d) Install the door at 90°.

Loosen Outer

screws

Summary of Contents for Profile















































Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands

GE Profile, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands