GE Profile Page 32 Owner'S Manual And Installation Instructions Download

Page: 32 / 46

Installation Instructions

CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

A cold water supply is required for automatic ice maker

operation. If there is not a cold water supply, you will

need to provide one. See Installing the Water Line section.
NOTES:
• Before making the connection to the refrigerator, be

sure the refrigerator power cord is not plugged into the

wall outlet.

• If your refrigerator does not have a water filter, we

recommend installing one if your water supply has

sand or particles that could clog the screen of the

refrigerator’s water valve. Install it in the water line

near the refrigerator. If using GE SmartConnect

™

Refrigerator Tubing Kit, you will need an additional tube

(WX08X10002) to connect the filter. Do not cut plastic

tube to install filter.

• Before connecting the water line to the house, purge

the house line for at least 2 minutes.

If you are using copper tubing, place a compression nut

and ferrule (sleeve) onto the end of the tubing coming

from the house cold water supply.
If you are using the GE SmartConnect

™

tubing, the nuts

are already assembled to the tubing.

If you are using copper tubing, insert the end of the

tubing into the refrigerator connection, at the back of the

refrigerator, as far as possible. While holding the tubing,

tighten the fitting.
If you are using GE SmartConnect

™

tubing, insert

the molded end of the tubing into the refrigerator

connection, at the back of the refrigerator, and tighten

the compression nut until it is hand tight. Then tighten

one additional turn with a wrench. Over tightening may

cause leaks.
Fasten the tubing into the clamp provided to hold it in

position. You may need to pry open the clamp.

1/4

”

Compression

Nut

Ferrule

(sleeve)

SmartConnect

™

Tubing

Refrigerator

Connection

INSTALLING THE REFRIGERATOR

(cont.)

1/4

“

Tubing

Tuyau de 1/4 po
Tubería de 1/4

“

Tubing Clamp

Bride

Abrazadera del tub

Summary of Contents for Profile















































Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands

GE Profile, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands