GE Profile Page 24 Owner'S Manual And Installation Instructions Download

Page: 24 / 46

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Do not install the refrigerator in a location exposed to

water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it fully

loaded.

CLEARANCES

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

Sides 1/8

”

(3 mm)

Top 1

”

(25 mm) Cabinet/Hinge Cover

Back 2

”

(50 mm)

REMOVE THE FRESH FOOD

DOOR HANDLE

Handle Design varies based on models, however

Installation is same.

Stainless steel and plastic handles:

Loosen the set screws with the 1/8” Allen wrench

and remove the handle.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a 1/4” Allen wrench.

REMOVE THE FREEZER DOOR HANDLE

Handle Design varies based on models, however

Installation is same.

Stainless steel and plastic handles:

Loosen the set screws with the 1/8” Allen wrench and

remove the handle.

NOTE: If the handle mounting fasteners need to be

tightened or removed, use a 1/4” Allen wrench.

Mounting

Fasteners

Leave film
on until after
installation

Mounting

Fasteners

Leave film
on until after
installation

Reinstall the handles using the same procedure as

removing.

REMOVING THE REFRIGERATOR DOORS

• IMPORTANT NOTE: This refrigerator is 36

” deep (31

”

for CD models). Doors and passageways leading to the

installation location must be at least 36

” wide in order to

leave the doors and handles attached to the refrigerator

while transporting it into the installation location. If

passageways are less than 36

”, the refrigerator doors

and handles can easily be scratched and damaged.

The top cap and doors can be removed to allow the

refrigerator to be safely moved indoors. If passageways

are less than 31

”, start with Step 1.

• If it is not necessary to remove doors, skip to Step

11. Leave tape and all packaging on doors until the

refrigerator is in the final location.

• NOTE: Use a padded hand truck to move this refrigerator.

Place the refrigerator on the hand truck with a side

against the truck. We strongly recommend that TWO

PEOPLE move and complete this installation.

Summary of Contents for Profile















































Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands

GE Profile, Owner'S Manual And Installation Instructions

Search results

Summary of Contents for Profile

Reviews:

Related manuals for Profile

Brands by name

Popular brands