GE Profile PFCF1RKZ Technical Service Manual Download | Manualshive

Page: 21 / 66

– 21 –

Ice System Airfl ow - (single drawer model shown)

The ice fan forces air up from the freezer into the ice door section via an inlet duct.

The ice fan is controlled by the main control board.

Air returns from the ice door section to the freezer compartment via an outlet duct.

ICE MAKER

FAN

FRESH FOOD

FREEZER

Evaporator

Cold Air
Mixed Air
Air Return To
Evaporator

Fresh Food

Ice Maker

Fan

Freezer

«
...
19
20
21
22
23
...
»

Summary of Contents for Profile PFCF1RKZ



































































Reviews:

No comments

Related manuals for Profile PFCF1RKZ

Brand: TCL Pages: 44

Brand: Crivit Pages: 77

Brand: GE Pages: 64

Brand: AYA Pages: 30

Brand: Saivod Pages: 39

Brand: NEFF Pages: 86

Brand: Beper Pages: 36

Brand: Galanz Pages: 16

Brand: Master Bilt Pages: 2

Brand: Pkm Pages: 76

Brand: Adler Europe Pages: 112

Brand: UNITED Pages: 22

8.436.545.201.527

Brand: Svan Pages: 80

Brand: Grundig Pages: 54

REFRIGERATOR / FREEZER COMBO HRF-6631RG

Brand: Haier Pages: 44

Brand: Haier Pages: 84

Brand: Haier Pages: 31

Brand: Samsung Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands